Kitz ADSL Broadband Information
adsl spacer  
Support this site
Home Broadband ISPs Tech Routers Wiki Forum
 
     
   Compare ISP   Rate your ISP
   Glossary   Glossary
 
Please login or register.

Login with username, password and session length
Advanced search  

News:

Author Topic: Is there a telnet resync command for DG834  (Read 4532 times)

Peter L

  • Just arrived
  • *
  • Posts: 7
Is there a telnet resync command for DG834
« on: March 14, 2010, 08:47:51 PM »
Hi there,

I was wondering if there was a command I could send (via telnet) to force my DG834 to perform a resync. At the moment I cycle the mains power which probably isnt a good idea over the long term. I have a DG834v1 with the latest firmware from DGTeam.  I know I can reboot the router via telnet with "reboot" command but I was wondering if there was a less dramatic way of forcing a resync i.e. another command I could use via telnet.

Peter

P.S. At the moment I find that my DG834 hangs on to the connection even when the SNR margin is bad (-2dB) and the error rate is high (HEC errors). I was thinking of writing a python script to monitor the stats and automatically force the router to resync.
Logged

roseway

  • Administrator
  • Senior Kitizen
  • *
  • Posts: 43573
  • Penguins CAN fly
    • DSLstats
Re: Is there a telnet resync command for DG834
« Reply #1 on: March 14, 2010, 10:27:43 PM »
I don't think I've seen a CLI manual for this type of router, which uses the AR7 chipset. If you telnet into it you might find that 'help' gives you a list of commands. With Broadcom based routers (e.g. DG834Gv4) you can use:

adslctl connection down
adslctl connection up
Logged
  Eric

Azzaka

  • Reg Member
  • ***
  • Posts: 572
  • SysAdmin
    • A Designers Work in Progress
Re: Is there a telnet resync command for DG834
« Reply #2 on: March 15, 2010, 09:29:22 AM »
Quote from: roseway on March 14, 2010, 10:27:43 PM
I don't think I've seen a CLI manual for this type of router, which uses the AR7 chipset. If you telnet into it you might find that 'help' gives you a list of commands. With Broadcom based routers (e.g. DG834Gv4) you can use:

adslctl connection down
adslctl connection up


The v1 doesnt use the AR7 chipset. The AR7 didnt start to be used till the v2's. I'll try and track it down for you but i think it was the globalspan/rockwell chip.
Logged
I Sync', I Auth', therefore I am.
Online

roseway

  • Administrator
  • Senior Kitizen
  • *
  • Posts: 43573
  • Penguins CAN fly
    • DSLstats
Re: Is there a telnet resync command for DG834
« Reply #3 on: March 15, 2010, 10:07:59 AM »
Ah, sorry, thanks for correcting me Azzaka.
Logged
  Eric

Azzaka

  • Reg Member
  • ***
  • Posts: 572
  • SysAdmin
    • A Designers Work in Progress
Re: Is there a telnet resync command for DG834
« Reply #4 on: March 15, 2010, 10:21:02 AM »
No worries, i did a lot of research on the AR7 when it all came out as an issue and I was also under the impression it was AR7 but I was also told it wasnt. It shows the same symptoms but is not AR7.. wierd.
Logged
I Sync', I Auth', therefore I am.
Online

jeffbb

  • Kitizen
  • ****
  • Posts: 2329
Re: Is there a telnet resync command for DG834
« Reply #5 on: March 15, 2010, 07:54:12 PM »
Hi
Just  read the original AR7 issue discussed with ZEN. then followed links http://www.linux-mips.org/wiki/AR7
this shows  Netgear DG834(G) (Version 1, 2 and 3 have AR7 Chipset, version 4 has Broadcom chipset)

is it any help ?
Regards Jeff
Logged
zen user

orainsear

  • Reg Member
  • ***
  • Posts: 635
Re: Is there a telnet resync command for DG834
« Reply #6 on: March 15, 2010, 08:14:41 PM »
Here is a link to an image of a v1 board: http://img208.imageshack.us/img208/5886/dg834gintow2.jpg

The chip is the TNETD7300GDU (AR7WRD).
Logged