Kitz ADSL Broadband Information
adsl spacer  
Support this site
Home Broadband ISPs Tech Routers Wiki Forum
 
     
   Compare ISP   Rate your ISP
   Glossary   Glossary
 
Please login or register.

Login with username, password and session length
Advanced search  

News:

Pages: 1 [2]

Author Topic: A little info please  (Read 4101 times)

licquorice

  • Reg Member
  • ***
  • Posts: 977
Re: A little info please
« Reply #15 on: August 22, 2021, 06:08:57 PM »

My only concern is that the wires are the wrong way around but as ive been told here that makes no difference.
all  though i would like it to be as it should.

I read that as one sentence, with the full stop as a comma due to the lower case 'a' hence my reply.  :)

Interesting how different people interpret things differently.  :)
Logged

burakkucat

  • Respected
  • Senior Kitizen
  • *
  • Posts: 38300
  • Over the Rainbow Bridge
    • The ELRepo Project
Re: A little info please
« Reply #16 on: August 22, 2021, 06:40:19 PM »

Interesting how different people interpret things differently.  :)

Yes, indeed.  :)
Logged
:cat:  100% Linux and, previously, Unix. Co-founder of the ELRepo Project.

Please consider making a donation to support the running of this site.

DANNYG

  • Member
  • **
  • Posts: 51
  • Gaming till the end.
Re: A little info please
« Reply #17 on: August 22, 2021, 07:01:25 PM »

I'm sorry for any confusion in my posts im not very well educated.
So i use spell check to try and make sense of the babble i write.
Logged

Alex Atkin UK

  • Addicted Kitizen
  • *****
  • Posts: 5260
    • Thinkbroadband Quality Monitors
Re: A little info please
« Reply #18 on: August 22, 2021, 11:29:38 PM »

All i done was clean it all up remove the junction box as it was such a state joined the wires and place them inside a single gang electrical box with a blanking plate for further accesses its a hundred times better than it was.
My only concern is that the wires are the wrong way around but as ive been told here that makes no difference.
all  though i would like it to be as it should.
Many thanks for helping.

How did you join the wires?  As in that case I think its a good idea to get a newer box as suggested so they are joined according to how Openreach would do it.  Would avoid any awkward questions later if you developed a fault.
Logged
Broadband: Zen Full Fibre 900 + Three 5G Routers: pfSense (Intel N100) + Huawei CPE Pro 2 H122-373 WiFi: Zyxel NWA210AX
Switches: Netgear MS510TXUP, Netgear MS510TXPP, Netgear GS110EMX My Broadband History & Ping Monitors

DANNYG

  • Member
  • **
  • Posts: 51
  • Gaming till the end.
Re: A little info please
« Reply #19 on: August 23, 2021, 12:11:04 AM »

I twisted them together.
I will be ordering the box tomorrow.
Logged

DANNYG

  • Member
  • **
  • Posts: 51
  • Gaming till the end.
Re: A little info please
« Reply #20 on: September 10, 2021, 10:02:48 AM »

Hi i received a junction box today could somebody be kind enough to tell what wires go were just out of curiosity while i await bt to fit i have an orange/white  a blue/white and a blue then x2 black copper cables.
Many thanks.
Logged

tubaman

  • Senior Kitizen
  • ******
  • Posts: 12507
Re: A little info please
« Reply #21 on: September 10, 2021, 12:11:35 PM »

The black pair go under the A and B screw terminals with the orange/white and blue/white on the A and B IDC (punch-down) connectors. The polarity does not matter.
 :)
Logged
BT FTTC 55/10 Huawei Cab - Zyxel VMG8924-B10A

DANNYG

  • Member
  • **
  • Posts: 51
  • Gaming till the end.
Re: A little info please
« Reply #22 on: September 10, 2021, 12:17:05 PM »

thank you.
Logged
Pages: 1 [2]
 

anything