Hi everyone, I now have a working FTTC line now i have noticed that Vectoring is currently set at 5 (VECT_UNCONFIGURED)
Here is my stats
Stats recorded 31 Oct 2019 21:14:42
DSLAM type / SW version: BDCM:0xa48c (164.140) / v0xa48c
Modem/router firmware: AnnexA version - A2pv6F039v.d26a
DSL mode: VDSL2 Profile 17a
Status: Showtime
Uptime: 7 hours 16 min 18 sec
Resyncs: 0 (since 31 Oct 2019 20:26:00)
Downstream Upstream
Line attenuation (dB): 22.4 0.0
Signal attenuation (dB): Not available on VDSL2
Connection speed (kbps): 39994 6023
SNR margin (dB): 8.1 5.6
Power (dBm): 13.2 -5.1
Interleave depth: 1283 1
INP: 3.50 0
G.INP: Not enabled Not enabled
Vectoring status: 5 (VECT_UNCONFIGURED)
RSCorr/RS (%): 0.0038 0.0007
RSUnCorr/RS (%): 0.0000 0.0000
ES/hour: 2.16 2.16
adsl info --stats
adsl: ADSL driver and PHY status
Status: Showtime
Last Retrain Reason: 0
Last initialization procedure status: 0
Max: Upstream rate = 6023 Kbps, Downstream rate = 56694 Kbps
Bearer: 0, Upstream rate = 6023 Kbps, Downstream rate = 39994 Kbps
Link Power State: L0
Mode: VDSL2 Annex B
VDSL2 Profile: Profile 17a
TPS-TC: PTM Mode(0x0)
Trellis: U:ON /D:ON
Line Status: No Defect
Training Status: Showtime
Down Up
SNR (dB): 8.1 5.5
Attn(dB): 22.4 0.0
Pwr(dBm): 13.2 -5.1
VDSL2 framing
Bearer 0
MSGc: 18 26
B: 31 175
M: 1 1
T: 64 41
R: 10 12
S: 0.0255 0.9273
L: 13200 1622
D: 1283 1
I: 42 94
N: 42 188
Counters
Bearer 0
OHF: 10685303 993295
OHFErr: 22 7
RS: 4103001217 1406505
RSCorr: 157705 9
RSUnCorr: 1781 0
Bearer 0
HEC: 300 0
OCD: 0 0
LCD: 0 0
Total Cells: 2016069793 0
Data Cells: 425917687 0
Drop Cells: 0
Bit Errors: 0 0
ES: 8 7
SES: 0 0
UAS: 23 23
AS: 26218
Bearer 0
INP: 3.50 0.00
INPRein: 0.00 0.00
delay: 8 0
PER: 2.45 9.54
OR: 78.26 26.83
AgR: 40072.04 6050.23
Bitswap: 5666/5666 7/7
Total time = 7 hours 17 min 21 sec
FEC: 157705 9
CRC: 22 7
ES: 8 7
SES: 0 0
UAS: 23 23
LOS: 0 0
LOF: 0 0
LOM: 0 0
Latest 15 minutes time = 2 min 21 sec
FEC: 33 0
CRC: 0 0
ES: 0 0
SES: 0 0
UAS: 0 0
LOS: 0 0
LOF: 0 0
LOM: 0 0
Previous 15 minutes time = 15 min 0 sec
FEC: 3146 0
CRC: 3 0
ES: 1 0
SES: 0 0
UAS: 0 0
LOS: 0 0
LOF: 0 0
LOM: 0 0
Latest 1 day time = 7 hours 17 min 21 sec
FEC: 157705 9
CRC: 22 7
ES: 8 7
SES: 0 0
UAS: 23 23
LOS: 0 0
LOF: 0 0
LOM: 0 0
Previous 1 day time = 0 sec
FEC: 0 0
CRC: 0 0
ES: 0 0
SES: 0 0
UAS: 0 0
LOS: 0 0
LOF: 0 0
LOM: 0 0
Since Link time = 7 hours 16 min 57 sec
FEC: 157705 9
CRC: 22 7
ES: 8 7
SES: 0 0
UAS: 0 0
LOS: 0 0
LOF: 0 0
LOM: 0 0
NTR: mipsCntAtNtr=0 ncoCntAtNtr=0
>
I am using the Zytel VMG1312-B10A so Vectoring should be supported, so my question is does DLM run the line with Vectoring off to get the stats before it places Vectoring on or have i setup the PTM settings wrong as i have on the Zytel disabled everything to do with ADSL and just left the VDSL options on.
If someone could point me on the right path as FTTC is new to me so i am on another learning curve.