Kitz ADSL Broadband Information
adsl spacer  
Support this site
Home Broadband ISPs Tech Routers Wiki Forum
 
     
   Compare ISP   Rate your ISP
   Glossary   Glossary
 
Please login or register.

Login with username, password and session length
Advanced search  

News:

Pages: [1] 2 3

Author Topic: DLM not working as it should  (Read 5812 times)

tommy45

  • Reg Member
  • ***
  • Posts: 627
DLM not working as it should
« on: October 31, 2019, 02:18:55 PM »
Dlm seems to be taking negative action  for no known reason,  the recorded error rates are well within the threshold MTBE always under 100 errored seconds per 24 hr period no ses even the fecs are lowish  , there are no errored  many months ago  dlm  reduced the SNR (downstream) to 4db  but set re trans to hi 50, but my sync was still the max 799952 it today without any logical reason  acted again  still 4db but increased the inp to 51
, this is only a small decrease on sync but my throughput  which was around 72 mbps is now around 68 mbps!!!! what a joke dlm is
DSLAM type / SW version:   BDCM:0xa48c (164.140) / v0xa48c
Modem/router firmware:     AnnexA version - A2pv6C038m.d24j
DSL mode:                  VDSL2 Profile 17a
Status:                    Showtime
Uptime:                     0 hour 26 min 33 sec
Resyncs:                   0 (since 31 Oct 2019 13:58:14)
         
            Downstream   Upstream
Line attenuation (dB):     13.7      0.0
Signal attenuation (dB):   Not available on VDSL2      
Connection speed (kbps):   78836      19999
SNR margin (dB):           4.3      15.1
Power (dBm):               12.4      3.9
Interleave depth:          8      1
INP:                       51.00      0
G.INP:                     Enabled      Not enabled
Vectoring status:          5 (VECT_UNCONFIGURED)      

RSCorr/RS (%):             0.0003      0.0002
RSUnCorr/RS (%):           0.0000      0.0000
ES/hour:                   0      0
Logged

Chrysalis

  • Content Team
  • Addicted Kitizen
  • *
  • Posts: 7402
  • VM Gig1 - AAISP CF
Re: DLM not working as it should
« Reply #1 on: October 31, 2019, 06:37:45 PM »
the ES threshold's are fast path, and will very likely be much lower with g.inp/interleave.

I dont know what they are but its probably significantly lower.

Sadly you only posted partial data, the most useful data is omitted from that telnet output.
Logged

tommy45

  • Reg Member
  • ***
  • Posts: 627
Re: DLM not working as it should
« Reply #2 on: October 31, 2019, 07:09:30 PM »
Here you go, Also i have been on  G.inp for years and it apart from in the begining has been only applied to the DS  i have had zero ds errors  only upstream  and an increased burst every time the phone rings of around 20 errored secs, this too has been ongoing for a while   but error rates since the SNR was lowered from 6 to 4db, and ret hi applied these error rates have been lower  the most they where before were around 120 per day,  they have been as low as 30 -80 per day  depending on how many incoming calls
Code: [Select]
xdslcmd info --stats
xdslcmd: ADSL driver and PHY status
Status: Showtime
Retrain Reason: 0
Last initialization procedure status: 0
Max: Upstream rate = 26503 Kbps, Downstream rate = 78376 Kbps
Bearer: 0, Upstream rate = 19999 Kbps, Downstream rate = 78836 Kbps
Bearer: 1, Upstream rate = 0 Kbps, Downstream rate = 0 Kbps
Link Power State: L0
Mode: VDSL2 Annex B
VDSL2 Profile: Profile 17a
TPS-TC: PTM Mode(0x0)
Trellis: U:ON /D:ON
Line Status: No Defect
Training Status: Showtime
Down Up
SNR (dB): 4.3 15.2
Attn(dB): 13.7 0.0
Pwr(dBm): 12.4 3.9
VDSL2 framing
Bearer 0
MSGc: -6 26
B: 243 237
M: 1 1
T: 0 42
R: 10 16
S: 0.0986 0.3781
L: 20618 5374
D: 8 1
I: 254 127
N: 254 254
Q: 8 0
V: 0 0
RxQueue: 88 0
TxQueue: 22 0
G.INP Framing: 18 0
G.INP lookback: 22 0
RRC bits: 0 24
Bearer 1
MSGc: 186 -6
B: 0 0
M: 2 0
T: 2 0
R: 16 0
S: 5.3333 0.0000
L: 48 0
D: 3 0
I: 32 0
N: 32 0
Q: 0 0
V: 0 0
RxQueue: 0 0
TxQueue: 0 0
G.INP Framing: 0 0
G.INP lookback: 0 0
RRC bits: 0 0
Counters
Bearer 0
OHF: 0 497350
OHFErr: 0 19
RS: 758078352 780375
RSCorr: 2878 77
RSUnCorr: 0 0
Bearer 1
OHF: 1167439 0
OHFErr: 0 0
RS: 14008529 0
RSCorr: 0 0
RSUnCorr: 0 0

Retransmit Counters
rtx_tx: 502694 0
rtx_c: 30 0
rtx_uc: 0 0

G.INP Counters
LEFTRS: 0 0
minEFTR: 78821 0
errFreeBits: 22548470 0

Bearer 0
HEC: 0 0
OCD: 0 0
LCD: 0 0
Total Cells: 2842905297 0
Data Cells: 70674513 0
Drop Cells: 0
Bit Errors: 0 0

Bearer 1
HEC: 0 0
OCD: 0 0
LCD: 0 0
Total Cells: 0 0
Data Cells: 0 0
Drop Cells: 0
Bit Errors: 0 0

ES: 0 16
SES: 0 0
UAS: 23 23
AS: 18753

Bearer 0
INP: 51.00 0.00
INPRein: 1.00 0.00
delay: 0 0
PER: 0.00 3.98
OR: 0.01 64.22
AgR: 78916.80 20063.54

Bearer 1
INP: 4.00 0.00
INPRein: 4.00 0.00
delay: 3 0
PER: 16.06 0.01
OR: 95.62 0.01
AgR: 95.62 0.01

Bitswap: 3066/3066 1/1

Total time = 5 hours 12 min 56 sec
FEC: 2878 77
CRC: 0 19
ES: 0 16
SES: 0 0
UAS: 23 23
LOS: 0 0
LOF: 0 0
LOM: 0 0
Latest 15 minutes time = 12 min 56 sec
FEC: 137 8
CRC: 0 0
ES: 0 0
SES: 0 0
UAS: 0 0
LOS: 0 0
LOF: 0 0
LOM: 0 0
Previous 15 minutes time = 15 min 0 sec
FEC: 156 1
CRC: 0 0
ES: 0 0
SES: 0 0
UAS: 0 0
LOS: 0 0
LOF: 0 0
LOM: 0 0
Latest 1 day time = 5 hours 12 min 56 sec
FEC: 2878 77
CRC: 0 19
ES: 0 16
SES: 0 0
UAS: 23 23
LOS: 0 0
LOF: 0 0
LOM: 0 0
Previous 1 day time = 0 sec
FEC: 0 0
CRC: 0 0
ES: 0 0
SES: 0 0
UAS: 0 0
LOS: 0 0
LOF: 0 0
LOM: 0 0
Since Link time = 5 hours 12 min 31 sec
FEC: 2878 77
CRC: 0 19
ES: 0 16
SES: 0 0
UAS: 0 0
LOS: 0 0
LOF: 0 0
LOM: 0 0
#
Logged

burakkucat

  • Respected
  • Senior Kitizen
  • *
  • Posts: 38300
  • Over the Rainbow Bridge
    • The ELRepo Project
Re: DLM not working as it should
« Reply #3 on: October 31, 2019, 07:37:07 PM »
Quote from: tommy45 on October 31, 2019, 07:09:30 PM
. . .  i have had zero ds errors  only upstream  and an increased burst every time the phone rings . . .

That is strongly indicative of a joint beginning to show high resistance and/or semi-conductive tendencies. Have you performed a quiet line test recently?
Logged
:cat:  100% Linux and, previously, Unix. Co-founder of the ELRepo Project.

Please consider making a donation to support the running of this site.

tommy45

  • Reg Member
  • ***
  • Posts: 627
Re: DLM not working as it should
« Reply #4 on: October 31, 2019, 08:10:24 PM »
I did one last week and not a noise out of place, sadly that burst of errors when the voltage increases for incoming calls I'm sure was pointed out to the last OR bod, a few years ago but nothing done about it , guess i need a more conscientious engineer? But if this adverse trend continues I'll be raising a fault with my ISP, unless i start hearing audible oddities during the quiet test that are easily reproduced, been in that situation before nearly cost me a lot of money for the privilege of a RWT result
Logged

ejs

  • Kitizen
  • ****
  • Posts: 2078
Re: DLM not working as it should
« Reply #5 on: October 31, 2019, 08:25:25 PM »
The INP value changing from 50 to 51 does not indicate that the DLM made any changes. The exact INP level, and various other parameters often vary slightly each time it connects even when the DLM has not changed anything. Something other than the DLM may have caused the disconnection.
Logged

tommy45

  • Reg Member
  • ***
  • Posts: 627
Re: DLM not working as it should
« Reply #6 on: October 31, 2019, 09:29:09 PM »
@02.56 in the morning i can see what else it could have been, no power outages 100% sure of that My Throughput is also significantly lower too,I have no visibility to my ip profile and haven't done for ages, Zen are aware  but never fixed, it also reports an incorrect sync rate again been ongoing since March this year
« Last Edit: October 31, 2019, 09:39:02 PM by tommy45 »
Logged

tommy45

  • Reg Member
  • ***
  • Posts: 627
Re: DLM not working as it should
« Reply #7 on: November 02, 2019, 01:38:57 PM »
Further to my previous post DLM has change the parameters again, it would appear this time to have reduced the Ds target SNR to 3db from the 4db it had been on for over 200 days, It also has increased the G.inp retx From 51-52 and the RX queuing level   without issue (re sync) as far as i can tell from the stats recorded, the latest stats here:
Code: [Select]
xdslcmd info --stats
xdslcmd: ADSL driver and PHY status
Status: Showtime
Retrain Reason: 0
Last initialization procedure status: 0
Max: Upstream rate = 26773 Kbps, Downstream rate = 82036 Kbps
Bearer: 0, Upstream rate = 19999 Kbps, Downstream rate = 79999 Kbps
Bearer: 1, Upstream rate = 0 Kbps, Downstream rate = 0 Kbps
Link Power State: L0
Mode: VDSL2 Annex B
VDSL2 Profile: Profile 17a
TPS-TC: PTM Mode(0x0)
Trellis: U:ON /D:ON
Line Status: No Defect
Training Status: Showtime
Down Up
SNR (dB): 3.6 15.1
Attn(dB): 13.8 0.0
Pwr(dBm): 12.3 4.3
VDSL2 framing
Bearer 0
MSGc: -6 26
B: 162 237
M: 1 1
T: 0 42
R: 8 16
S: 0.0647 0.3781
L: 21128 5374
D: 8 1
I: 171 127
N: 171 254
Q: 8 0
V: 2 0
RxQueue: 136 0
TxQueue: 34 0
G.INP Framing: 18 0
G.INP lookback: 31 0
RRC bits: 0 24
Bearer 1
MSGc: 186 -6
B: 0 0
M: 2 0
T: 2 0
R: 16 0
S: 5.3333 0.0000
L: 48 0
D: 3 0
I: 32 0
N: 32 0
Q: 0 0
V: 0 0
RxQueue: 0 0
TxQueue: 0 0
G.INP Framing: 0 0
G.INP lookback: 0 0
RRC bits: 0 0
Counters
Bearer 0
OHF: 0 1382947
OHFErr: 0 15
RS: 2402543056 680046
RSCorr: 19067 139
RSUnCorr: 0 0
Bearer 1
OHF: 2430692 0
OHFErr: 0 0
RS: 29167564 0
RSCorr: 0 0
RSUnCorr: 0 0

Retransmit Counters
rtx_tx: 503153 0
rtx_c: 127 0
rtx_uc: 0 0

G.INP Counters
LEFTRS: 0 0
minEFTR: 79980 0
errFreeBits: 47632458 0

Bearer 0
HEC: 0 0
OCD: 0 0
LCD: 0 0
Total Cells: 1711502681 0
Data Cells: 18721766 0
Drop Cells: 0
Bit Errors: 0 0

Bearer 1
HEC: 0 0
OCD: 0 0
LCD: 0 0
Total Cells: 0 0
Data Cells: 0 0
Drop Cells: 0
Bit Errors: 0 0

ES: 0 14
SES: 0 0
UAS: 24 24
AS: 39044

Bearer 0
INP: 52.00 0.00
INPRein: 1.00 0.00
delay: 0 0
PER: 0.00 3.98
OR: 0.01 64.22
AgR: 80244.76 20063.54

Bearer 1
INP: 4.00 0.00
INPRein: 4.00 0.00
delay: 3 0
PER: 16.06 0.01
OR: 95.62 0.01
AgR: 95.62 0.01

Bitswap: 8384/8384 2/2

Total time = 10 hours 51 min 8 sec
FEC: 19067 139
CRC: 0 15
ES: 0 14
SES: 0 0
UAS: 24 24
LOS: 0 0
LOF: 0 0
LOM: 0 0
Latest 15 minutes time = 6 min 8 sec
FEC: 144 1
CRC: 0 1
ES: 0 1
SES: 0 0
UAS: 0 0
LOS: 0 0
LOF: 0 0
LOM: 0 0
Previous 15 minutes time = 15 min 0 sec
FEC: 501 0
CRC: 0 1
ES: 0 1
SES: 0 0
UAS: 0 0
LOS: 0 0
LOF: 0 0
LOM: 0 0
Latest 1 day time = 10 hours 51 min 8 sec
FEC: 19067 139
CRC: 0 15
ES: 0 14
SES: 0 0
UAS: 24 24
LOS: 0 0
LOF: 0 0
LOM: 0 0
Previous 1 day time = 0 sec
FEC: 0 0
CRC: 0 0
ES: 0 0
SES: 0 0
UAS: 0 0
LOS: 0 0
LOF: 0 0
LOM: 0 0
Since Link time = 10 hours 50 min 43 sec
FEC: 19067 139
CRC: 0 15
ES: 0 14
SES: 0 0
UAS: 0 0
LOS: 0 0
LOF: 0 0
LOM: 0 0
# I now have the max sync rate again, But only a throughput of 68mbps My IP profile on G.inp used to be 77.35  surely i should be seeing a throughput of around 72/73 mbps not 68, I still have no access to what the  IP profile is the only info i have is within zen's portal , which is giving an incorrect sync speed
Logged

tommy45

  • Reg Member
  • ***
  • Posts: 627
Re: DLM not working as it should
« Reply #8 on: November 04, 2019, 02:15:08 PM »
Been in touch with zen's tech support they ran a kbd GEA test and here's what it reported

Description GEA service test completed and no fault found.
Main Fault Location OK
Sync Status In Sync
Downstream Speed 76.6 Mbps
Upstream Speed 20.0 Mbps
Appointment Required N
Fault Target Fix Time
Fault Report Advised N
Estimated Line Length In Metres 343.8
Upstream Rate Assessment Very Good
Downstream Rate Assessment Very Good
Interference Pattern Not Detected
Service Impact No Impact Observed
Home Wiring Problem Not Detected
Downstream Policing Discard Rate 0.0
Customer Traffic Level Upstream and Downstream Traffic Detected
Technology VDSL
DP Type External
Current 15Min Bin Retrains 0
Last 15Min Bin Retrains 0
NTE Power Status PowerOn
Voice Line Test Result Not Run - Unable to run
Bridge Tap Not Detected
Radio Frequency Ingress Not Detected
Repetitive Electrical Impulse Noise Not Detected
Cross Talk Not Detected
Profile Name 0.128M-80M Downstream 4dB, Retransmission High
             0.128M-20M Upstream, Error Protection Off
------------------------------------------------------------------------------------------------------------------

Is the speed observed supposed to be sync or throughput? the target snr would appear to be incorrect

[Moderator edited to correct the mangled formatting at the end of the report.]
« Last Edit: November 04, 2019, 05:07:27 PM by burakkucat »
Logged

Black Sheep

  • Helpful
  • Addicted Kitizen
  • *
  • Posts: 5722
Re: DLM not working as it should
« Reply #9 on: November 04, 2019, 03:07:53 PM »
It is synch speed ................ if you think about it, you can never attain the full 20Mbps Upstream (that is being reported in those stats) on throughput.  :)
Logged

tommy45

  • Reg Member
  • ***
  • Posts: 627
Re: DLM not working as it should
« Reply #10 on: November 04, 2019, 04:13:30 PM »
Quote from: Black Sheep on November 04, 2019, 03:07:53 PM
It is synch speed ................ if you think about it, you can never attain the full 20Mbps Upstream (that is being reported in those stats) on throughput.  :)
If that is the case  then that result can't of been from my circuit or the sync has been incorrectly reported it has never been 76.6 And i don't think what the modem is saying is wrong
Code: [Select]
xdslcmd info --stats
xdslcmd: ADSL driver and PHY status
Status: Showtime
Retrain Reason: 0
Last initialization procedure status: 0
Max: Upstream rate = 26837 Kbps, Downstream rate = 81808 Kbps
Bearer: 0, Upstream rate = 19999 Kbps, Downstream rate = 79999 Kbps
Bearer: 1, Upstream rate = 0 Kbps, Downstream rate = 0 Kbps
Link Power State: L0
Mode: VDSL2 Annex B
VDSL2 Profile: Profile 17a
TPS-TC: PTM Mode(0x0)
Trellis: U:ON /D:ON
Line Status: No Defect
Training Status: Showtime
Down Up
SNR (dB): 3.6 15.2
Attn(dB): 13.8 0.0
Pwr(dBm): 12.3 4.3
VDSL2 framing
Bearer 0
MSGc: -6 26
B: 162 237
M: 1 1
T: 0 42
R: 8 16
S: 0.0647 0.3781
L: 21128 5374
D: 8 1
I: 171 127
N: 171 254
Q: 8 0
V: 2 0
RxQueue: 136 0
TxQueue: 34 0
G.INP Framing: 18 0
G.INP lookback: 31 0
RRC bits: 0 24
Bearer 1
MSGc: 186 -6
B: 0 0
M: 2 0
T: 2 0
R: 16 0
S: 5.3333 0.0000
L: 48 0
D: 3 0
I: 32 0
N: 32 0
Q: 0 0
V: 0 0
RxQueue: 0 0
TxQueue: 0 0
G.INP Framing: 0 0
G.INP lookback: 0 0
RRC bits: 0 0
Counters
Bearer 0
OHF: 0 931594
OHFErr: 0 111
RS: 763969760 1159627
RSCorr: 119257 807
RSUnCorr: 0 0
Bearer 1
OHF: 13808497 0
OHFErr: 0 0
RS: 165701230 0
RSCorr: 0 0
RSUnCorr: 0 0

Retransmit Counters
rtx_tx: 503664 0
rtx_c: 638 0
rtx_uc: 0 0

G.INP Counters
LEFTRS: 0 0
minEFTR: 79980 0
errFreeBits: 270594784 0

Bearer 0
HEC: 0 0
OCD: 0 0
LCD: 0 0
Total Cells: 4057509605 0
Data Cells: 187072127 0
Drop Cells: 0
Bit Errors: 0 0

Bearer 1
HEC: 0 0
OCD: 0 0
LCD: 0 0
Total Cells: 0 0
Data Cells: 0 0
Drop Cells: 0
Bit Errors: 0 0

ES: 0 101
SES: 0 0
UAS: 24 24
AS: 221802

Bearer 0
INP: 52.00 0.00
INPRein: 1.00 0.00
delay: 0 0
PER: 0.00 3.98
OR: 0.01 64.22
AgR: 80244.76 20063.54

Bearer 1
INP: 4.00 0.00
INPRein: 4.00 0.00
delay: 3 0
PER: 16.06 0.01
OR: 95.62 0.01
AgR: 95.62 0.01

Bitswap: 63200/63200 7/7

Total time = 1 days 13 hours 37 min 6 sec
FEC: 119257 807
CRC: 0 111
ES: 0 101
SES: 0 0
UAS: 24 24
LOS: 0 0
LOF: 0 0
LOM: 0 0
Latest 15 minutes time = 7 min 6 sec
FEC: 292 0
CRC: 0 0
ES: 0 0
SES: 0 0
UAS: 0 0
LOS: 0 0
LOF: 0 0
LOM: 0 0
Previous 15 minutes time = 15 min 0 sec
FEC: 569 7
CRC: 0 1
ES: 0 1
SES: 0 0
UAS: 0 0
LOS: 0 0
LOF: 0 0
LOM: 0 0
Latest 1 day time = 13 hours 37 min 6 sec
FEC: 28406 214
CRC: 0 38
ES: 0 35
SES: 0 0
UAS: 0 0
LOS: 0 0
LOF: 0 0
LOM: 0 0
Previous 1 day time = 24 hours 0 sec
FEC: 48260 302
CRC: 0 31
ES: 0 28
SES: 0 0
UAS: 0 0
LOS: 0 0
LOF: 0 0
LOM: 0 0
Since Link time = 2 days 13 hours 36 min 41 sec
FEC: 119257 807
CRC: 0 111
ES: 0 101
SES: 0 0
UAS: 0 0
LOS: 0 0
LOF: 0 0
LOM: 0 0
#
Logged

kitz

  • Administrator
  • Senior Kitizen
  • *
  • Posts: 33884
  • Trinity: Most guys do.
    • http://www.kitz.co.uk
Re: DLM not working as it should
« Reply #11 on: November 04, 2019, 06:57:32 PM »
It definitely is sync speed.

One thing to bear in mind is some of the data on a GEA test may be ~14 days out of date especially when it comes to the reported DLM profile.
Logged
Please do not PM me with queries for broadband help as I may not be able to respond.
-----
How to get your router line stats :: ADSL Exchange Checker

ejs

  • Kitizen
  • ****
  • Posts: 2078
Re: DLM not working as it should
« Reply #12 on: November 04, 2019, 07:43:16 PM »
The GEA test reports something different from the "sync speed" (actual net data rate) on a retransmission high profile, for the same reason as for why you get a lower IP profile on a retransmission high profile. Depending on how much of the GEA test results the ISP copies and pastes, there'll be another section with something like some min / max / current speeds which will match the modem "sync speed", even on a retransmission high profile.
Logged

NewtronStar

  • Kitizen
  • ****
  • Posts: 4898
Re: DLM not working as it should
« Reply #13 on: November 04, 2019, 10:00:11 PM »
Its a INP/RTX High issue which lowers your thoughput from 96% to 91 or 92%
Profile Name 0.128M-80M Downstream 4dB, Retransmission High

INP:      52.00      0.00
INPRein:   1.00      0.00
delay:      0      0
PER:      0.00      3.98
OR:      0.01      64.22
AgR:      80244.76   20063.5

John should be able to give you the low-downs on this subject.
« Last Edit: November 04, 2019, 10:19:25 PM by NewtronStar »
Logged

tommy45

  • Reg Member
  • ***
  • Posts: 627
Re: DLM not working as it should
« Reply #14 on: November 04, 2019, 10:37:59 PM »
[One image removed at the request of originator]

Yes i had read the thread about the 88% IP profile  incorrectly set, which if i check the IP profile figure in the zen portal it is 88% not 92%  which it should be  88% of 79999kbps =70399 (70.40) When it should be (73.60) giving a throughput of approx 71mbps  not 68mbps, i have  attached a ss of the same figure that backs up it's set to 88% and one of all i get when i run further diags on the bt performance tester , which has been this way since april or may this year when zen started getting incorrect sync speed info from btw
And here is a set of modem stats  from a day before DLM messed things up 212 days uptime in total  this was 211 days
My throughput was around 72-73 mbps  then as it had been since april or may  this year  before that the circuit had  lasted over 600 days without a re sync and throughput was around 74 mbps

Code: [Select]
=~=~=~=~=~=~=~=~=~=~=~= Plink log 2019.10.30 06:00:09 =~=~=~=~=~=~=~=~=~=~=~=

xdslcmd info --stats
xdslcmd: ADSL driver and PHY status
Status: Showtime
Retrain Reason:   1
Last initialization procedure status:   0
Max:   Upstream rate = 26598 Kbps, Downstream rate = 79288 Kbps
Bearer:   0, Upstream rate = 19999 Kbps, Downstream rate = 79952 Kbps
Bearer:   1, Upstream rate = 0 Kbps, Downstream rate = 0 Kbps
Link Power State:   L0
Mode:         VDSL2 Annex B
VDSL2 Profile:      Profile 17a
TPS-TC:         PTM Mode(0x0)
Trellis:      U:ON /D:ON
Line Status:      No Defect
Training Status:   Showtime
      Down      Up
SNR (dB):    4.3       14.6
Attn(dB):    13.7       0.0
Pwr(dBm):    12.3       3.6
         VDSL2 framing
         Bearer 0
MSGc:      -6      26
B:      243      237
M:      1      1
T:      0      42
R:      10      16
S:      0.0972      0.3781
L:      20910      5374
D:      8      1
I:      254      127
N:      254      254
Q:      8      0
V:      0      0
RxQueue:      88      0
TxQueue:      22      0
G.INP Framing:      18      0
G.INP lookback:      22      0
RRC bits:      0      24
         Bearer 1
MSGc:      186      -6
B:      0      0
M:      2      0
T:      2      0
R:      16      0
S:      5.3333      0.0000
L:      48      0
D:      3      0
I:      32      0
N:      32      0
Q:      0      0
V:      0      0
RxQueue:      0      0
TxQueue:      0      0
G.INP Framing:      0      0
G.INP lookback:      0      0
RRC bits:      0      0
         Counters
         Bearer 0
OHF:      0      4227255
OHFErr:      5      14989
RS:      1052430704      4291836
RSCorr:      5544066      98254
RSUnCorr:   0      0
         Bearer 1
OHF:      1136344466      0
OHFErr:      0      0
RS:      751230968      0
RSCorr:      14      0
RSUnCorr:   0      0

         Retransmit Counters
rtx_tx:      502212      0
rtx_c:      63982      0
rtx_uc:      46474      0

         G.INP Counters
LEFTRS:      13      0
minEFTR:   79959      0
errFreeBits:   1288426123      0

         Bearer 0
HEC:      0      0
OCD:      0      0
LCD:      0      0
Total Cells:   1797097489      0
Data Cells:   4229222725      0
Drop Cells:   0
Bit Errors:   0      0

         Bearer 1
HEC:      0      0
OCD:      0      0
LCD:      0      0
Total Cells:   0      0
Data Cells:   0      0
Drop Cells:   0
Bit Errors:   0      0

ES:      15      13711
SES:      11      0
UAS:      57      46
AS:      18252760

         Bearer 0
INP:      50.00      0.00
INPRein:   1.00      0.00
delay:      0      0
PER:      0.00      3.98
OR:      0.01      64.22
AgR:      80034.45   20063.54

         Bearer 1
INP:      4.00      0.00
INPRein:   4.00      0.00
delay:      3      0
PER:      16.06      0.01
OR:      95.62      0.01
AgR:      95.62   0.01

Bitswap:   8793205/8793205      1477/1477

Total time = 1 days 18 hours 29 min 47 sec
FEC:      5667594      99543
CRC:      560      15152
ES:      15      13711
SES:      11      0
UAS:      57      46
LOS:      1      0
LOF:      9      0
LOM:      0      0
Latest 15 minutes time = 14 min 47 sec
FEC:      231      2
CRC:      0      1
ES:      0      1
SES:      0      0
UAS:      0      0
LOS:      0      0
LOF:      0      0
LOM:      0      0
Previous 15 minutes time = 15 min 0 sec
FEC:      202      0
CRC:      0      0
ES:      0      0
SES:      0      0
UAS:      0      0
LOS:      0      0
LOF:      0      0
LOM:      0      0
Latest 1 day time = 18 hours 29 min 47 sec
FEC:      19477      564
CRC:      0      86
ES:      0      74
SES:      0      0
UAS:      0      0
LOS:      0      0
LOF:      0      0
LOM:      0      0
Previous 1 day time = 24 hours 0 sec
FEC:      26026      470
CRC:      0      76
ES:      0      63
SES:      0      0
UAS:      0      0
LOS:      0      0
LOF:      0      0
LOM:      0      0
Since Link time = 49 days 17 hours 2 min 47 sec
FEC:      5544066      98254
CRC:      5      14989
ES:      4      13560
SES:      0      0
UAS:      0      0
LOS:      0      0
LOF:      0      0
LOM:      0      0


HELLO HG612
xdslcmd info --pbParams
xdslcmd: ADSL driver and PHY status
Status: Showtime
Retrain Reason:   1
Last initialization procedure status:   0
Max:   Upstream rate = 26598 Kbps, Downstream rate = 79288 Kbps
Bearer:   0, Upstream rate = 19999 Kbps, Downstream rate = 79952 Kbps
Bearer:   1, Upstream rate = 0 Kbps, Downstream rate = 0 Kbps
Discovery Phase (Initial) Band Plan
US: (7,32) (871,1205) (1972,2782)
DS: (33,859) (1216,1961) (2793,3970)
Medley Phase (Final) Band Plan
US: (7,32) (871,1205) (1972,2782)
DS: (33,859) (1216,1961) (2793,3970)
     VDSL Port Details        Upstream        Downstream
Attainable Net Data Rate:       26598 kbps          79288 kbps
Actual Aggregate Tx Power:          3.6 dBm           12.3 dBm
 =========================================================================================
  VDSL Band Status    U0    U1    U2    U3    U4    D1    D2    D3
  Line Attenuation(dB):    3.1    15.3    22.3     N/A     N/A    8.8    19.4    29.8   
Signal Attenuation(dB):    3.1    14.5    21.5     N/A     N/A    11.8    19.3    29.8   
   SNR Margin(dB):    14.8    14.7    14.6     N/A     N/A    4.2    4.3    4.2   
    TX Power(dBm):   -11.5   -27.8    3.5     N/A     N/A    7.9    7.8    7.0   

Good Bye HG612
« Last Edit: October 05, 2020, 07:10:03 AM by roseway »
Logged
Pages: [1] 2 3
« previous next »
 

anything