Kitz ADSL Broadband Information
adsl spacer  
Support this site
Home Broadband ISPs Tech Routers Wiki Forum
 
     
   Compare ISP   Rate your ISP
   Glossary   Glossary
 
Please login or register.

Login with username, password and session length
Advanced search  

News:

Author Topic: Need help with CLI Commands Asus DSL-N16 VDSL  (Read 3098 times)

MadAbdo

  • Member
  • **
  • Posts: 11
Need help with CLI Commands Asus DSL-N16 VDSL
« on: July 05, 2019, 10:11:26 AM »

Hello,

I want to know list of SSH commands can be used with asus DSL-N16 VDSL Router
https://wikidevi.com/wiki/ASUS_DSL-N16

i want to change SNR and set channel type to Fast instead of interleaved,

my cabinet already accept the commands, i know that because i tried it with ZTE H168N and it's worked to change the SNR and and the channel type to fastpath
with these commands

Code: [Select]
wan dmt2 set snrmoffset xx xx (snr tweak)
wan dmt2 set path x (0-2 channel profile fast interleaved)
wan vdsl2 set target_snrm xx (snr tweak vdsl2)
wan vdsl2 set manual_pms on/off (something about channel profile)

but now i have this ASUS router that using MediaTek chip and need the commands to make changes to my line as i did using ZTE Router

Thanks .
Logged

ejs

  • Kitizen
  • ****
  • Posts: 2078
Re: Need help with CLI Commands Asus DSL-N16 VDSL
« Reply #1 on: July 06, 2019, 08:37:24 AM »

Aren't the commands the same?

Looking at the tc3162_dmt.ko module from a DSL-N16 firmware, the output of "strings tc3162_dmt.ko | fgrep usage" gives:

Code: [Select]
usage: wan adsl sethp [opt]
usage: wan ghs set toneselect <1=t9+t37/ 2=t17+t45/ 3=t25+t53/ 4=1+2/ 5=2+3/ 6=1+3/ 0=1+2+3>
usage: wan ghs set usifft <us_ifft_size>  <us_ifft_fill_type,1=complex conjurate/2=fill zero>
usage: wan ghs set nearvendorid <value>
usage: wan ghs set sendcxntghs   <on/off?>  <on/off ?>
usage: w ghs set annex [a|b|i|j|al][m][bj][aijlm][auto]
usage: wan dmt2 nm cofw [std|nonstd]
usage: wan dmt2 set fakebg [on|off]
usage: wan dmt2 nm cnxt [1|0]
usage: wan dmt2 db tlb [tlb ID]
usage: wan dmt2 db set [off/auto/db_index]
Show PMDRead usage1: [Hlog|Hlin|QLN|SNRPerTone|LATN|SATN|SNRM|ATTNDR|NearACTATP|FarACTATP
usage: wan dmt2 set ginp_test [on|off]
usage: wan dmt2 set fltrvref [value]
usage: wan dmt2 set largeD 0/1/2
usage: wan dmt2 set SRACrc [0/1 OFF/ON]
usage: wan dmt2 set esrelink on/off [threshold]
usage: wan dmt2 set medley threshold [snr threshold] [tone ratio]
usage: wan dmt2 set pilotretrain [0/1/2/3]
usage: wan dmt2 set pilotdata [on|off]
usage: wan dmt2 set linkstate [0|3]
usage: wan dmt2 set attenoffset [value]
usage: wan dmt2 set crcrelink [value]
usage: wan dmt2 set snrmoffset [Intl*512] [Fast*512]
usage: wan dmt2 set depth [value]
usage: wan dmt2 set Rs off/on/[Max R_value]
usage: wan dmt2 set vref [val1] [val2] [val3] [val4]
usage: wan dmt2 set blackout [start_tone>31] [end_tone<512]
usage: wan dmt2 set pilot [tone]
usage: wan dmt2 set path 0/1/2(Fast/Inter/Free) path
usage: wan dmt2 set Slowerbound [value]
usage: wan dmt2 set inp [INP value *100]
usage: wan dmt2 set pcb [dspcb] [uspcb]
usage: wan dmt2 set updatesync [on|off|default]
usage: wan dmt2 set sync [on|off] [sync position] [txrxsample] [0~2047]
usage: wan dmt2 set rxfiltertype <value>
usage: wan dmt2 set txfiltertype <value>
usage: wan dmt2 set rxfltrgain [value]
usage: wan dmt2 set txfltrgain [value]
usage: wan dmt2 set fdm_cfg mode[0|1|2|3] type[1|2]
usage: wan dmt2 set tcm [on|off]
usage: wan dmt set teqvref <value>
usage: wan dmt set dbgflag [value]
usage: wan dmt set  softdecode <on/off>
usage: wan dmt set bngrelinkflag <0/1>
usage: wan dmt set agcvref <value1> <value2> <value3>
usage: wan dmt set syncflag <on/off>
usage: wan dmt set up32relinkflag <0/1>
usage: wan dmt set attenoffset <vaule>
usage: wan dmt set  medleytone <start tone> <stop tone>
usage: wan dmt set snrmoffset <value[(+/-)db*512]>
usage: wan dmt set snroffset <value[(+/-)db*512]>
usage: wan dmt set pilotdata t64_value t_pilot_value
usage: wan dmt set pilottone <value>
usage: w dmt set pilotretrain [1/3]
usage: w dmt set pilotretrain [3] [0/1]
usage: wan dmt set minsnrm <value>
usage: wan dmt set txfiltertype <value>
usage: wan dmt set db rxfiltertype <value>
usage: wan dmt set txfiltgain <value>
usage: wan dmt set teqtones <start tone> <end tone>
usage: wan dmt set txrvbtones <start tone> <end tone>
usage: wan dmt set  fm <value>
usage: wan dmt set tcm [on|off]
usage:wan dmt aoc gwtst [value]
usage:wan dmt aoc bwtst [value]
usage: wan dmt aoc bitswap [on/off] [on/off]
usage: wan dmt pilot [cnt] [pause opt]
usage:wan dmt db tlb [value]
usage: wan dmt db set  [off/auto/db_index]
usage: wan vdsl2 show online_snrm
usage: wan vdsl2 set olr_timing [timing][sos_x][sos_y][sos_z]
usage: w vdsl2 test inm [on/off]
usage: wan vdsl2 show st_avg_snrm (tx/rx)
usage: wan vdsl2 show errpwr [init|st]
usage: wan vdsl2 set ginp_sra [on/off/go]
usage: wan vdsl2 set ginp_sos [go/off]
usage: wan vdsl2 test ovhd [diag|inv|pm|mgcnt|clreoc|nsf|pmd]
usage: wan vdsl2 show vector
usage: wan vdsl2 show st_soc_info
usage: wan vdsl2 show pms_pmd [tx|rx]
usage: wan vdsl2 show pmdtestparam (hlog/qln/snr/attndr)
usage: wan vdsl2 show snrm [st]
usage: wan vdsl2 show snr [init|st]
usage: wan vdsl2 show new_bgtbl rx
usage: wan vdsl2 show bgtbl [tx|rx]
usage: wan vdsl2 set gsd [value]
usage: wan vdsl2 set gso [value]
usage: wan vdsl2 set gvt_mode [value]
usage: wan vdsl2 set hrt_delay [tx sym] [tx dtu] [rx sym] [rx dtu]
usage: wan vdsl2 set sync_sym [val]
usage: wan vdsl2 set ginp_test [on|off]
usage: wan vdsl2 set max_ds_rate [valus/8] (unit:kbps)
usage: wan vdsl2 set max_us_rate [valus/8] (unit:kbps)
usage: wan vdsl2 set tr115 [on|off]
usage: wan vdsl2 set cd_us_band_adj [on|off|auto]
usage: wan vdsl2 set ds_est_new [on|off]
usage: wan vdsl2 set ds_est_new min [x] ,X = (0.1 * x) dB
usage: wan vdsl2 set ds_est_new adsl [y], Y = (1/1000 * y)
usage: wan vdsl2 set ds_est_new echo [z], Z = z dB(>=0)
usage: wan vdsl2 set cd_us_comp_value [value]
usage: wan vdsl2 set usbp_check [on|off]
usage: wan vdsl2 set kikp [0~13][0~11]
usage: wan vdsl2 set rtslog_from [rtslog_state_from]
usage: wan vdsl2 set v_noise [on|off]
usage: w vdsl2 set pilot tone [num: 1|2|3|4] [tone1]...
usage: w vdsl2 set pilot band [idx: 0|1|2|3] [start] [stop]
usage: w vdsl2 set pilot method [method: 0|1|2|3|4|5]
usage: w vdsl2 set pilot start [on|off]
usage: wan vdsl2 set tx_cp_len [val]
usage: wan vdsl2 set tx_comp on/off
usage: wan vdsl2 tx_comp tone start_tone relay_tone stop_tone
usage: wan vdsl2 tx_comp value start_tone_psd_comp relay_tone_psd_comp stop_tone_psd_comp
usage: wan vdsl2 tx_comp offsetrelay_tone_psd_comp_offset_non_upbo relay_tone_psd_comp_offset_upbo
usage: wan vdsl2 set txgain_deploy [0|1|2]
usage: wan vdsl2 set txpsd_drop_check [on|off]
usage: wan vdsl2 set txpsd_drop_limit [val]
usage: wan vdsl2 set txpwr_diff [val]
usage: wan vdsl2 set txpwr_limit [on/off] [value/none]
usage: wan vdsl2 set mode_select [on|off]
usage: wan vdsl2 set rxpcb [on|off][rxpcb_mask]
usage: wan vdsl2 set detect_tone_offset [index1] [index2] [index3] [index4]
usage: wan vdsl2 set ds_tone [ds_lowest_tone] [ds_highest_tone]
usage: wan vdsl2 set us_tone [us_lowest_tone] [us_highest_tone]
usage: wan vdsl2 set tx_pcb [on|off] [pcb_mask]
usage: wan vdsl2 set rfi_cancel [on|off]
usage: wan vdsl2 set rx_win [on/off]
usage: wan vdsl2 set tx_win [on/off][win_len]
usage: wan vdsl2 set rxfltr_gain [val]
usage: wan vdsl2 set rxfltr_ref [val]
usage: wan vdsl2 set ta_offset [val]
usage: wan vdsl2 set byte_med[R_MED 1|2][O_MED 1|2]
usage: wan vdsl2 set kl0 [val:0~1280]
usage: wan vdsl2 set kl0_offset [val]
usage: wan vdsl2 set kl0_method [0|1]
usage: wan vdsl2 set upbo [on|off]
usage: wan vdsl2 set rx_blackout 0 : ds blackout off
usage: wan vdsl2 set teq_fir_coeff [a2] [a3] [a4]
usage: wan vdsl2 set rx_fltr_type [fltr_for_cd_phase] [fltr_for_training_phase]
usage: wan vdsl2 set tx_fltr_type [fltr_for_cd_phase] [fltr_for_training_phase]
usage: wan vdsl2 set tx_fltr_gain [tx_fltr_gain] [tx_fltr_dout_scale] [tx_upshift_bit]
usage: wan vdsl2 set tx_gain_offset [value]
usage: wan vdsl2 set st_period [period(sec)]
usage: wan vdsl2 set st_task [on/off]
usage: wan vdsl2 set st_dbg [on/off/olr]
usage: wan vdsl2 set tpstc_type [0(ptm only)/1(ptm+atm)]
usage: wan vdsl2 set gvector [1|2]
usage: wan vdsl2 set amd [0|1|2|3]
usage: wan vdsl2 set sync_check [on/off]
usage: wan vdsl2 set one_bit [on|off]
usage: wan vdsl2 set st_target_snrm [snrm]
usage: wan vdsl2 set target_snrm [snrm_dB]
usage: wan vdsl2 set manual_pms [on|off]
usage: wan vdsl2 set inp_snrm_roc [inp_min(symbol)] [snrm_offset(dB)]
usage: wan vdsl2 set roc [on/off]
usage: wan vdsl2 set dual_lp [on|off]
usage: wan vdsl2 set fake_pms [on|off]
usage: wan vdsl2 set search_time_pms [time (# symbols)]
usage: wan vdsl2 set rscg_pms [on|off]
usage: wan vdsl2 set largedelay_pms [on|off]
usage: wan vdsl2 set inpdelay_pms [inp_min0] [inp_min1] [delay_max0] [delay_max1]
usage: wan vdsl2 set ndr_pms [msg_min] [ndr_min0] [ndr_min1] [ndr_max0] [ndr_max1]
usage: wan vdsl2 set ins_inp [on/off]
usage: wan vdsl2 set sos [on/off/go]
usage: wan vdsl2 set sra_trans_method [0(non-seg)/1(seg)]
usage: wan vdsl2 set sra_l_target off/[bits]
usage: wan vdsl2 set sra_step [on|off]
usage: wan vdsl2 set sra [on|off]
usage: wan vdsl2 set bs_param [snrm] [trigger] [scan_tone_num] [wait_cnt] [scan_start_idx] [scan_end_idx]
usage: wan vdsl2 set bs_1bit_change [on|off]
usage: wan vdsl2 set autobs [on|off]
usage: wan vdsl2 set bs_tx [on|off]
usage: wan vdsl2 set bs [on|off]
usage: wan vdsl2 set mgcnt_ovhd_test [on|off]
usage: wan vdsl2 set agc_vref [val1] [val2] [val3] [val4]
usage: wan vdsl2 set tcm [on|off]
usage: pmd [single|muti|nextmulti|block|hlog|qln|snr]
usage:[id|auxid|self]
usage: wan hwdmt afe set txfc <value>
usage: wan hwdmt afe set vld <BIAS> <CPP> <CPN>
usage: wan hwdmt afe set vld <REG> <DATA>
usage: wan hwdmt afe set ldv_gain <value: 0/6/12
usage: wan hwdmt afe set rxlpf 0(Bypass)/1(8M)/2(4M)/3(2M)
usage: wan hwdmt afe set rxlpf 0(27M)/1(17M)/2(8.5M)
usage: wan hwdmt afe set rxgain  1(ADSL Mode)  <eclna_atten> <eclna_gain> <lnhpf_gain> <aaf_gain> <sf_onoff> <hpf bypass>
usage: wan hwdmt afe set rxgain  2(VDSL Mode)  <lna_atten> <lna_gain> <aaf_atten> <aaf_gain>
usage: wan hwdmt afe set rxgain  value(value not 1 and 2 means cancel rxgain setting) !
usage: wan hwdmt afe set txgain <value: 0~7>. Correspond value[-12 -6 -2 -1 0 1 2 3]
usage: wan hwdmt afe set iampgain <value N(0~4) G1(1~4) G2(1~6) G3(1~6)>
usage: wan hwdmt afe set iampgain N <value 0~4>)
usage: wan hwdmt afe set iampgain G1 <value 1~4>)
usage: wan hwdmt afe set iampgain G2 <value 1~6>)
usage: wan hwdmt afe set iampgain G3 <value 1~6>)
usage: w hw show ecir [start_idx end_idx (72~1023)]
usage: w rts fast_boardsop [on/off]
Logged

MadAbdo

  • Member
  • **
  • Posts: 11
Re: Need help with CLI Commands Asus DSL-N16 VDSL
« Reply #2 on: July 10, 2019, 06:29:20 AM »

i will check them as soon as possible, do you know which commands i can use also to improve my connection ?

thank you so much
Logged