Kitz ADSL Broadband Information
adsl spacer  
Support this site
Home Broadband ISPs Tech Routers Wiki Forum
 
     
   Compare ISP   Rate your ISP
   Glossary   Glossary
 
Please login or register.

Login with username, password and session length
Advanced search  

News:

Pages: [1] 2

Author Topic: DSLstats 6.5 with cisco hardware?  (Read 2686 times)

bndwdthseekr

  • Member
  • **
  • Posts: 23
DSLstats 6.5 with cisco hardware?
« on: April 02, 2019, 09:19:21 PM »

I'm trying to get dsl stats to grab info from my cisco ISR with a VA-DSL-A modem card. Not sure if I'm missing something, but I haven't been able to get anything yet, accept custom commands showing in the log.

Below, you can see what my output looks like... any ideas? Is my line any good?  :) hoping for some of that sweet SWEET vdsl2, or atleast adsl2+ soon.

Also, is there a reason I don't see more people here with cisco hardware? I have been very pleased with this card, zero errors on my line now! Of course the shielded/grounded cat5e coming straight from the outdoor splitter/NID to the modem doesn't hurt... there's something to be said about properly terminating your shielded cable and plugging directly into the modem instead of stacking more connectors from a wall plug ;D

Code: [Select]
show controll vdsl 0/0/0 bit-alloc
Controller VDSL 0/0/0 is UP

Daemon Status: Up

XTU-R (DS) XTU-C (US)
Chip Vendor ID: 'BDCM' 'IFTN'
Chip Vendor Specific:   0x0000 0x71B0
Chip Vendor Country:    0xB500 0xB500
Modem Vendor ID: 'CSCO' '    '
Modem Vendor Specific:  0x4602 0x0000
Modem Vendor Country:   0xB500 0x0000
Serial Number Near:    xxxxxxxxxxx 2911/K9 15.7(3)M3
Serial Number Far:     
Modem Version Near:    15.7(3)M3
Modem Version Far:     0x71b0

Modem Status: TC Sync (Showtime!)

DSL Config Mode: AUTO
Trained Mode: G.992.1 (ADSL) Annex A
TC Mode: ATM
Selftest Result: 0x00
DELT configuration: enabled
DELT state: successful

Full inits: 1
Failed full inits: 0
Short inits: 0
Failed short inits: 1

-----------------cut firmware info

Modem FW  Version: 4.14L.04A
Modem PHY Version: A2pv6C039m.d24o_rc1
Trellis: ON   ON
SRA: enabled enabled
 SRA count: 1 1
Bit swap: enabled enabled
 Bit swap count: 0 331
Line Attenuation: 25.0 dB 14.0 dB
Signal Attenuation: 25.0 dB   0.0 dB
Noise Margin: 20.1 dB 17.0 dB
Attainable Rate: 10492 kbits/s 1356 kbits/s
Actual Power: 19.8 dBm 11.1 dBm
Total FECC: 0 0
Total ES: 0 0
Total SES: 0 0
Total LOSS: 0 0
Total UAS: 28 28
Total LPRS: 0 0
Total LOFS: 0 0
Total LOLS: 0 0


    DS Channel1   DS Channel0 US Channel1   US Channel0
Speed (kbps):           0         6944          0         1024
SRA Previous Speed:       0            0          0            0
Previous Speed:           0            0          0            0
Total Cells:           0    514079332          0            0
User Cells:           0     85138245          0            0
Reed-Solomon EC:          0            0          0            0
CRC Errors:           0            0          0            0
Header Errors:           0            0          0            0
Interleave (ms):       0.00         0.25       0.00         0.25
Actual INP:        0.00         0.00       0.00         0.00

Training Log : Stopped
Training Log Filename : usbflash0:ciscoext/DSLtrainlog


*****************************
* Subcarrier Bit Allocation *
*****************************


Downstream Subcarrier Bit Allocation --

measured data = 256, num_data = 256
0000 00 00 00 00 00 00 06 05 06 08 09 0A 0B 0B 0C 0C
0010 0C 0D 0D 0D 0D 0D 0C 0D 0C 0D 0B 0B 0B 0B 0A 0A
0020 00 00 02 02 02 02 03 03 03 04 04 05 05 05 05 06
0030 06 07 07 08 08 09 09 09 0A 0A 0A 0A 0A 0B 0A 0B
0040 00 0B 0B 0B 0B 0B 0B 0A 0B 0B 0B 0B 0B 0B 0B 0B
0050 0B 0B 0B 0B 0B 0B 0B 0B 0A 0A 0A 0A 0A 0B 0A 0A
0060 0A 0A 0A 0A 0A 0A 0A 0A 0A 0A 0A 0A 0A 0A 0A 0A
0070 0A 0A 09 0A 0A 0A 0A 0A 09 09 0A 0A 0A 0A 09 09
0080 09 09 09 09 09 09 09 09 09 09 0A 09 09 0A 02 09
0090 09 09 08 09 09 09 09 09 09 09 09 09 09 09 09 09
00A0 08 08 09 09 08 09 09 09 09 09 09 09 09 09 09 08
00B0 09 09 08 08 08 08 09 09 09 09 09 08 08 08 08 08
00C0 08 08 08 08 08 08 08 08 08 08 08 08 08 08 08 08
00D0 08 08 08 08 08 08 08 08 08 08 08 08 08 08 08 08
00E0 08 08 08 07 08 07 07 07 07 07 07 07 07 07 07 07
00F0 07 07 07 07 07 06 06 06 06 05 05 05 04 04 03 00

BFR#show version | s uptime
BFR uptime is 8 hours, 45 minutes
« Last Edit: April 02, 2019, 11:10:43 PM by bndwdthseekr »
Logged

roseway

  • Administrator
  • Senior Kitizen
  • *
  • Posts: 39553
  • Penguins CAN fly
    • DSLstats
Re: DSLstats 6.5 with cisco hardware?
« Reply #1 on: April 03, 2019, 11:02:18 AM »

I'm sorry, but I know absolutely nothing about the equipment you mention. It doesn't appear to have a Broadcom DSL chipset, in which case it wouldn't be possible to make DSLstats work with it.
Logged
  Eric

bndwdthseekr

  • Member
  • **
  • Posts: 23
Re: DSLstats 6.5 with cisco hardware?
« Reply #2 on: April 03, 2019, 02:03:21 PM »

Chip Vendor ID:      'BDCM'

looks like broadcom to me... I happen to know that the modem contains a broadcom bmips4350 chip. Doesn't DSLstats pull the info directly from the console anyway? is there a way I can specify which line each parameter appears on?
Logged

kitz

  • Administrator
  • Senior Kitizen
  • *
  • Posts: 32287
  • Trinity: Most guys do.
    • http://www.kitz.co.uk
Re: DSLstats 6.5 with cisco hardware?
« Reply #3 on: April 03, 2019, 02:06:04 PM »

Code: [Select]
XTU-R (DS) XTU-C (US)
This ^ could be slightly confusing as XTU-R is remote (modem)  XTU-C is central office (dslam). 
The (DS) & (US) is reverse of what we would usually expect to see.

The  EHWIC-VA-DSL-A is "based on the Broadcom chipset" although it doesn't say which particular one.
I suspect it's using Cisco custom f/w in a similar way to what TP-link does, so that the standard BCM commands may not be available...  thus limited information what you can get using DSLstats. 


Ref
Quote
EHWIC-VA-DSL-A (supporting multimode ADSL2/ADSL2+/VDSL technologies based on the Broadcom chipset):

Download firmware from http://software.cisco.com/download/navigator.html                         

Logged
Please do not PM me with queries for broadband help as I may not be able to respond.
-----
How to get your router line stats :: ADSL Exchange Checker

kitz

  • Administrator
  • Senior Kitizen
  • *
  • Posts: 32287
  • Trinity: Most guys do.
    • http://www.kitz.co.uk
Re: DSLstats 6.5 with cisco hardware?
« Reply #4 on: April 03, 2019, 02:12:48 PM »

Chip Vendor ID:      'BDCM'

looks like broadcom to me... I happen to know that the modem contains a broadcom bmips4350 chip. Doesn't DSLstats pull the info directly from the console anyway? is there a way I can specify which line each parameter appears on?


Our posts crossed.   I was typing my reply as you posted yours.

DSLstats uses the standard BCM CLI commands to get information.   
However, some manufacturers make their own custom f/w with their own custom commands.   TP-link do this with all/most of their modems, which unfortunately stops DLSstats from being able to get all the data it needs :(
Logged
Please do not PM me with queries for broadband help as I may not be able to respond.
-----
How to get your router line stats :: ADSL Exchange Checker

bndwdthseekr

  • Member
  • **
  • Posts: 23
Re: DSLstats 6.5 with cisco hardware?
« Reply #5 on: April 03, 2019, 02:42:47 PM »

ahh, thanks for clearing that up  :D

I am using ADSLmonitor and am able to grab stats from any command by specifying line number... its a shame I can't do the same with DSLstats... hopefully next release I can, I don't really care about setting transmit power or anything as I can do that manually.

Here's a snip of the modem card console log:
Code: [Select]
************************************
* VDSL Chipset Console Log (size - 38784 bytes)*
************************************
Linux version 3.4.11-rt19 (ragvasud@bgl-ads-1344) (gcc version 4.6.2 (Buildroot 2011.11) ) #2 SMP PREEMPT Fri Feb 3 10:55:28 IST 20    17


*** NVRAM Setup  ***


96368VVW prom init

CPU revision is: 0002a031 (Broadcom BMIPS4350)


anyway this is what I'm using, and how I have it hooked in to the service




« Last Edit: April 03, 2019, 06:00:35 PM by bndwdthseekr »
Logged

burakkucat

  • Global Moderator
  • Senior Kitizen
  • *
  • Posts: 28285
  • Over the Rainbow Bridge
    • The ELRepo Project
Re: DSLstats 6.5 with cisco hardware?
« Reply #6 on: April 03, 2019, 10:01:26 PM »

Interesting pictures (and maps) will always attract the attention of a curious kitteh!  :D 

I have to ask the two questions: Am I right to say that you are not located in the UK? And, if you won't mind disclosing the information, who is your service provider, please?

From the Cisco CLI via the console, are you able to drop back to an underlying (Busybox) shell? If yes, take a look to see if there is a command like "xdslcmd",  "xdslctl" or similar available.
Logged
:cat:  100% Linux and, previously, Unix. Co-founder of the ELRepo Project.

Please consider making a donation to support the running of this site.

bndwdthseekr

  • Member
  • **
  • Posts: 23
Re: DSLstats 6.5 with cisco hardware?
« Reply #7 on: April 04, 2019, 02:51:33 AM »

Nope not in the UK, I'm across the pond  ;D and the provider (for everyone who isn't a moderator here and already looked it up) is Frontier. lol I'm not scared...

maps? ???

As for the avaliable commands... There's no access to to the modem console that I know of, except for a few things in the cisco config. in my first post you can see the output for 'sh controller vdsl 0/0/0' which should provide all the info needed for the graphing in  DSLstats

Next time I power the system off for something, Ill pull out the modem and check for a serial header, although I doubt cisco left me any
« Last Edit: April 04, 2019, 04:45:18 AM by bndwdthseekr »
Logged

roseway

  • Administrator
  • Senior Kitizen
  • *
  • Posts: 39553
  • Penguins CAN fly
    • DSLstats
Re: DSLstats 6.5 with cisco hardware?
« Reply #8 on: April 04, 2019, 07:22:40 AM »

It's true that the output of the command which you showed in your first post seems to provide enough information for some useful graphs. However this would require a substantial rewrite of the parsing code in DSLstats, and I'm sorry to tell you that this isn't going to be possible. The time I spend in front of a screen is very limited by an eyesight difficulty, so I can't undertake anything more than minor tweaking.
Logged
  Eric

bndwdthseekr

  • Member
  • **
  • Posts: 23
Re: DSLstats 6.5 with cisco hardware?
« Reply #9 on: April 04, 2019, 10:14:15 AM »

aww too bad! I think ADSL monitor only goes up to 1,104khz and doesn't have the nice graphing or http server, not to mention the linux support...

On the up side, it sounds like I'm getting bumped up to ADSL2+ soon how much bandwidth do you all think I can expect with my stats? Are there any disadvantage besides loosing a couple mbps on the down side if I can convince the company to put me on annex M?


« Last Edit: April 04, 2019, 10:18:15 AM by bndwdthseekr »
Logged

jelv

  • Helpful
  • Kitizen
  • *
  • Posts: 1467
Re: DSLstats 6.5 with cisco hardware?
« Reply #10 on: April 04, 2019, 11:15:38 AM »

I'd wait and see what you get on ADSL2+ before considering Annex M.
Logged
Line rental: Pulse8, Broadband: AAISP Home::1 FTTC 80/20, Mobile: id Mobile

bndwdthseekr

  • Member
  • **
  • Posts: 23
Re: DSLstats 6.5 with cisco hardware?
« Reply #11 on: April 04, 2019, 03:36:17 PM »

It's true that the output of the command which you showed in your first post seems to provide enough information for some useful graphs. However this would require a substantial rewrite of the parsing code in DSLstats, and I'm sorry to tell you that this isn't going to be possible. The time I spend in front of a screen is very limited by an eyesight difficulty, so I can't undertake anything more than minor tweaking.

Any chance you could get me the complete modem status layout that works? I could probably filter the output and make it work that way.
Logged

jelv

  • Helpful
  • Kitizen
  • *
  • Posts: 1467
Re: DSLstats 6.5 with cisco hardware?
« Reply #12 on: April 04, 2019, 03:57:53 PM »

Here are dumps of the telnet data from my modem.

I've truncated some of the lists where it goes up to the tones in use as it bust the maximum message size on here.

Code: [Select]
xdslcmd info --stats
xdslcmd: ADSL driver and PHY status
Status: Showtime
Retrain Reason: 0
Last initialization procedure status: 0
Max: Upstream rate = 24947 Kbps, Downstream rate = 86484 Kbps
Bearer: 0, Upstream rate = 19999 Kbps, Downstream rate = 79999 Kbps
Bearer: 1, Upstream rate = 0 Kbps, Downstream rate = 0 Kbps
Link Power State: L0
Mode: VDSL2 Annex B
VDSL2 Profile: Profile 17a
TPS-TC: PTM Mode(0x0)
Trellis: U:ON /D:ON
Line Status: No Defect
Training Status: Showtime
Down Up
SNR (dB): 7.7 15.1
Attn(dB): 9.1 0.0
Pwr(dBm): 12.8 -6.5
VDSL2 framing
Bearer 0
MSGc: -6 26
B: 130 237
M: 1 1
T: 0 42
R: 8 16
S: 0.0518 0.3781
L: 21468 5374
D: 16 1
I: 139 127
N: 139 254
Q: 16 0
V: 14 0
RxQueue: 60 0
TxQueue: 20 0
G.INP Framing: 18 0
G.INP lookback: 20 0
RRC bits: 0 24
Bearer 1
MSGc: 186 -6
B: 0 0
M: 2 0
T: 2 0
R: 16 0
S: 5.3333 0.0000
L: 48 0
D: 3 0
I: 32 0
N: 32 0
Q: 0 0
V: 0 0
RxQueue: 0 0
TxQueue: 0 0
G.INP Framing: 0 0
G.INP lookback: 0 0
RRC bits: 0 0
Counters
Bearer 0
OHF: 0 3686622
OHFErr: 13 3389
RS: 3143412880 1895708
RSCorr: 196432 20635
RSUnCorr: 0 0
Bearer 1
OHF: 155492855 0
OHFErr: 0 0
RS: 1865913525 0
RSCorr: 13 0
RSUnCorr: 0 0

Retransmit Counters
rtx_tx: 7204155 0
rtx_c: 10876 0
rtx_uc: 15 0

G.INP Counters
LEFTRS: 131 0
minEFTR: 79999 0
errFreeBits: 3047634521 0

Bearer 0
HEC: 0 0
OCD: 0 0
LCD: 0 0
Total Cells: 1991463197 0
Data Cells: 1141327291 0
Drop Cells: 0
Bit Errors: 0 0

Bearer 1
HEC: 0 0
OCD: 0 0
LCD: 0 0
Total Cells: 0 0
Data Cells: 0 0
Drop Cells: 0
Bit Errors: 0 0

ES: 8 2957
SES: 0 0
UAS: 28 28
AS: 2497659

Bearer 0
INP: 48.00 0.00
INPRein: 0.00 0.00
delay: 0 0
PER: 0.00 3.98
OR: 0.01 64.22
AgR: 80614.82 20063.54

Bearer 1
INP: 4.00 0.00
INPRein: 4.00 0.00
delay: 3 0
PER: 16.06 0.01
OR: 95.62 0.01
AgR: 95.62 0.01

Bitswap: 261989/261999 7878/7878

Total time = 1 days 21 hours 48 min 7 sec
FEC: 196432 20635
CRC: 13 3389
ES: 8 2957
SES: 0 0
UAS: 28 28
LOS: 0 0
LOF: 0 0
LOM: 0 0
Latest 15 minutes time = 3 min 7 sec
FEC: 0 5
CRC: 0 1
ES: 0 1
SES: 0 0
UAS: 0 0
LOS: 0 0
LOF: 0 0
LOM: 0 0
Previous 15 minutes time = 15 min 0 sec
FEC: 40 60
CRC: 0 6
ES: 0 4
SES: 0 0
UAS: 0 0
LOS: 0 0
LOF: 0 0
LOM: 0 0
Latest 1 day time = 21 hours 48 min 7 sec
FEC: 3114 452
CRC: 0 109
ES: 0 98
SES: 0 0
UAS: 0 0
LOS: 0 0
LOF: 0 0
LOM: 0 0
Previous 1 day time = 24 hours 0 sec
FEC: 3027 480
CRC: 0 98
ES: 0 90
SES: 0 0
UAS: 0 0
LOS: 0 0
LOF: 0 0
LOM: 0 0
Since Link time = 28 days 21 hours 47 min 39 sec
FEC: 196432 20635
CRC: 13 3389
ES: 8 2957
SES: 0 0
UAS: 0 0
LOS: 0 0
LOF: 0 0
LOM: 0 0
#

Code: [Select]
xdslcmd info --Bits
xdslcmd: ADSL driver and PHY status
Status: Showtime
Retrain Reason: 0
Last initialization procedure status: 0
Max: Upstream rate = 24892 Kbps, Downstream rate = 86484 Kbps
Bearer: 0, Upstream rate = 19999 Kbps, Downstream rate = 79999 Kbps
Bearer: 1, Upstream rate = 0 Kbps, Downstream rate = 0 Kbps
Tone number      Bit Allocation
   0 0
   1 0
   2 0
   3 0
   4 0
   5 0
   6 0
   7 4
   8 6
   9 7
   10 8
   11 9
   12 10
   13 10
   14 11
   15 11
   16 11
   17 11
   18 10
   19 10
   20 10
   21 11
   22 10
   23 10
   24 10
   25 10
...
(goes up to tone 4095 on VDSL)
#

Code: [Select]
xdslcmd info --pbParams
xdslcmd: ADSL driver and PHY status
Status: Showtime
Retrain Reason: 0
Last initialization procedure status: 0
Max: Upstream rate = 24892 Kbps, Downstream rate = 86484 Kbps
Bearer: 0, Upstream rate = 19999 Kbps, Downstream rate = 79999 Kbps
Bearer: 1, Upstream rate = 0 Kbps, Downstream rate = 0 Kbps
Discovery Phase (Initial) Band Plan
US: (7,32) (871,1205) (1972,2782)
DS: (33,859) (1216,1961) (2793,3959)
Medley Phase (Final) Band Plan
US: (7,32) (871,1205) (1972,2782)
DS: (33,859) (1216,1961) (2793,3959)
  VDSL Port Details   Upstream   Downstream
Attainable Net Data Rate:     24892 kbps     86484 kbps
Actual Aggregate Tx Power:    -   6.5 dBm      12.8 dBm
====================================================================================
  VDSL Band Status U0 U1 U2 U3 U4 D1 D2 D3
  Line Attenuation(dB): 3.8 10.2 13.7 N/A N/A 5.1 11.2 17.1
Signal Attenuation(dB): 3.8 9.7 12.9 N/A N/A 5.9 11.1 17.1
        SNR Margin(dB): 15.0 15.1 15.1 N/A N/A 7.7 7.7 7.7
         TX Power(dBm): -20.6 -33.0 -6.7 N/A N/A 9.1 7.7 7.0
#

Code: [Select]
xdslcmd info --QLN
xdslcmd: ADSL driver and PHY status
Status: Showtime
Retrain Reason: 0
Last initialization procedure status: 0
Max: Upstream rate = 24995 Kbps, Downstream rate = 86484 Kbps
Bearer: 0, Upstream rate = 19999 Kbps, Downstream rate = 79999 Kbps
Bearer: 1, Upstream rate = 0 Kbps, Downstream rate = 0 Kbps
Tone number      QLN
   0 -160.0000
   1 -160.0000
   2 -160.0000
   3 -160.0000
   4 -160.0000
   5 -160.0000
   6 -160.0000
   7 -160.0000
   8 -120.0000
   9 -120.0000
   10 -120.0000
   11 -120.0000
   12 -120.0000
   13 -120.0000
   14 -120.0000
   15 -120.0000
   16 -121.0000
   17 -121.0000
   18 -121.0000
   19 -121.0000
   20 -121.0000
   21 -121.0000
   22 -121.0000
   23 -121.0000
   24 -118.5000
   25 -118.5000
...
(goes up to tone 4095 on VDSL)
#

Code: [Select]
xdslcmd info --Hlog
xdslcmd: ADSL driver and PHY status
Status: Showtime
Retrain Reason: 0
Last initialization procedure status: 0
Max: Upstream rate = 24995 Kbps, Downstream rate = 86484 Kbps
Bearer: 0, Upstream rate = 19999 Kbps, Downstream rate = 79999 Kbps
Bearer: 1, Upstream rate = 0 Kbps, Downstream rate = 0 Kbps
Tone number      Hlog
   0 -96.0000
   1 -96.0000
   2 -96.0000
   3 -96.0000
   4 -96.0000
   5 -96.0000
   6 -96.0000
   7 -96.2500
   8 -7.5000
   9 -7.5000
   10 -7.5000
   11 -7.5000
   12 -7.5000
   13 -7.5000
   14 -7.5000
   15 -7.5000
   16 -3.5625
   17 -3.5625
   18 -3.5625
   19 -3.5625
   20 -3.5625
   21 -3.5625
   22 -3.5625
   23 -3.5625
   24 -3.1875
   25 -3.1875
...
(goes up to tone 4095 on VDSL)
#

Code: [Select]
xdslcmd info --SNR
xdslcmd: ADSL driver and PHY status
Status: Showtime
Retrain Reason: 0
Last initialization procedure status: 0
Max: Upstream rate = 25055 Kbps, Downstream rate = 86484 Kbps
Bearer: 0, Upstream rate = 19999 Kbps, Downstream rate = 79999 Kbps
Bearer: 1, Upstream rate = 0 Kbps, Downstream rate = 0 Kbps
Tone number      SNR
   0 0.0000
   1 0.0000
   2 0.0000
   3 0.0000
   4 0.0000
   5 0.0000
   6 0.0000
   7 0.0000
   8 29.0000
   9 29.0000
   10 29.0000
   11 29.0000
   12 29.0000
   13 29.0000
   14 29.0000
   15 29.0000
   16 44.0000
   17 44.0000
   18 44.0000
   19 44.0000
   20 44.0000
   21 44.0000
   22 44.0000
   23 44.0000
   24 43.5000
   25 43.5000
...
(goes up to tone 4095 on VDSL)
#
« Last Edit: April 04, 2019, 04:00:40 PM by jelv »
Logged
Line rental: Pulse8, Broadband: AAISP Home::1 FTTC 80/20, Mobile: id Mobile

bndwdthseekr

  • Member
  • **
  • Posts: 23
Re: DSLstats 6.5 with cisco hardware?
« Reply #13 on: April 05, 2019, 12:21:17 PM »

Well... a little FYI to noobs like me who are using this hardware in the future... the following command allows direct console access to the card!

Code: [Select]
test vdsl 0/0/0 modem exec
I feel kinda dumb now....  :D atleast I found it though, right? I knew there had to be a way, but cisco doesn't make these types of things easy to google... NOT AT ALL!

I'm not even sure if cisco wants me posting this publicly as hard as it was to find lol, but jezus... I thought this was a cut down version, guess not!

Code: [Select]
The output of the command is :
adsl
adslctl
ash
bash
bcm_boot_launcher
bftpd
bpm
bpmctl
brctl
busybox
cat
chmod
consoled
cp
date
df
dhcpc
dhcpd
dsldiagd
dslmgmt
dumpmem
ebtables
echo
ethctl
ethswctl
false
gdbserver
ippd
iptables
kill
ln
ls
mkdir
mknod
mount
ping
pppd
ps
pwd
pwr
pwrctl
rm
send_cms_msg
setmem
sh
sleep
smd
sshd
ssk
swmdk
sync
telnetd
true
udhcpd
umount
xdslctl
xtables-multi
xtm
xtmctl


BFR#test vdsl 0/0/0 modem exec /bin/adsl
The output of the command is :
Usage: /bin/adsl start [--up] <configure command options>
       /bin/adsl stop
       /bin/adsl connection [--up] [--down] [--loopback] [--reverb]
           [--medley] [--noretrain] [--L3] [--diagmode] [--L0]
           [--tones <r1-r2,r3-r4,...>] [--normal] [--freezeReverb] [--freezeMedley]
       /bin/adsl configure/configure1 [--mod <a|d|l|t|2|p|e|m|M3|M5|v>] [--lpair <(i)nner|(o)uter>]
           [--trellis <on|off>] [--snr <snrQ4>] [--bitswap <on|off>] [--sesdrop <on|off>]
           [--sra <on|off>] [--CoMinMgn <on|off>] [--i24k <on|off>] [--phyReXmt <0xBitMap-UsDs>]
           [--Ginp <0xBitMap-UsDs>] [--TpsTc <0xBitMap-AvPvAaPa>] [--monitorTone <on|off>]
           [--profile <0x00 - 0xFF>|<"8a |8b |8c |8d |12a |12b |17a |30a">] [--us0 <on|off>]
           [--dynamicD <on|off>] [--dynamicF <on|off>] [--SOS <on|off>] [--maxDataRate <maxDsDataRateKbps maxUsDataRateKbps maxAggrDataRateKbps>]
           [--forceJ43 <on|off>] [--toggleJ43B43 <on|off>]
       /bin/adsl bert [--start <#seconds>] [--stop] [--show]
       /bin/adsl afelb [--time <sec>] [--tones] [--signal <1/2/8>]
       /bin/adsl qlnmntr [--time <sec>] [--freq <msec>]
       /bin/adsl inm [--start <INMIATO> <INMIATS><INMCC><INM_INPEQ_MODE><INM_INPEQ_FORMAT>] [--show]
       /bin/adsl snrclamp [--shape <shapeId>] [--bpshape [bpIndex-bpLevel,]]
       /bin/adsl nlnm [--show ] [--setThld <Thld_Num_Tones>]
       /bin/adsl diag [--logstart <nBytes>] [--logpause] [--logstop] [--loguntilbufferfull <nBytes>] [--loguntilretrain <nBytes>] [--dumpBuf <sizeKb>]
       /bin/adsl info [--state] [--show] [--stats] [--SNR] [--QLN] [--Hlog] [--Hlin] [--HlinS] [--Bits]
           [--pbParams] [--linediag] [--linediag1] [--reset] [--vendor] [--cfg]
       /bin/adsl profile [--show] [--save] [--restore]
       /bin/adsl --version
       /bin/adsl --help
« Last Edit: April 05, 2019, 01:16:33 PM by bndwdthseekr »
Logged

krypton

  • Reg Member
  • ***
  • Posts: 127
Re: DSLstats 6.5 with cisco hardware?
« Reply #14 on: April 05, 2019, 06:05:41 PM »

And the most important question: Did you get DSLstats running?
Logged
Pages: [1] 2
 

anything