Kitz ADSL Broadband Information
adsl spacer  
Support this site
Home Broadband ISPs Tech Routers Wiki Forum
 
     
   Compare ISP   Rate your ISP
   Glossary   Glossary
 
Please login or register.

Login with username, password and session length
Advanced search  

News:

Pages: 1 2 [3] 4 5

Author Topic: VMG1312-B10D new Web GUI 2.0 on V5.13(AAXA.8)C0?  (Read 4632 times)

tiffy

  • Reg Member
  • ***
  • Posts: 549
Re: VMG1312-B10D new Web GUI 2.0 on V5.13(AAXA.8)C0?
« Reply #30 on: November 04, 2018, 03:35:53 PM »

For the serial-console, CFE> prompt method, the required command is --

ATUR                Upload router firmware to flash from TFTP

(TFTP = trivial file transfer protocol.)

Many thanks for the further informat.

Regarding our earlier subject in this thread, applying Hashcat to decrypt a SHA-512 format character string, tried the following experiment:

From previous 1312-B10D FW revision V.5.13(AAXA.5) when the crypt character string was MD5 encoded, this Hashcat search line worked on my very modest Intel GUI desktop PC producing the correct result in under a minute.

hashcat64 -O -m 500 -a 3 -w 3 --force -D 1,2 root.hash ?h?h?h?h?h?hde
(last 2 characters were given to achieve a reasonable time on my system)

Now ran with SHA-512 format selected and new character string in root.hash:

hashcat64 -O -m 1800 -a 3 -w 3 --force -D 1,2 root.hash ?h?h?h?h?h?hde
(-m 500 changed to -m 1800 for SHA-512 format)

This command line was accepted by Hashcat but the PC "locked up" (tried twice) while initialising.
Concluded that the SHA-512 format Hashcat operation requires resources well beyond my PC's capabilities.
Logged
Plusnet 40/10 - DSLStats/RPi - ZyXEL VMG1312-B10A - Huawei Cab - MDWS (sadly gone 12/03/18)

tiffy

  • Reg Member
  • ***
  • Posts: 549
Re: VMG1312-B10D new Web GUI 2.0 on V5.13(AAXA.8)C0?
« Reply #31 on: November 04, 2018, 03:53:47 PM »

@jelv

Quote
What login are you using?

I only get ZySH which if I key ? shows the available commands - no stats available!

Ahh, I'am using Windows 8.1 command window (as administrator) on my desktop PC and I certainly don't get a ZySH> prompt hence the confusion !

From Win cmd prompt, telnet, open (IP address), login, pw, arrive @ Busybox command prompt as below:

Code: [Select]
BusyBox v1.20.1 (2017-04-20 00:36:56 CST) built-in shell (ash)
Enter 'help' for a list of built-in commands.

#

Same story with Windows 10 on my laptop PC..
Logged
Plusnet 40/10 - DSLStats/RPi - ZyXEL VMG1312-B10A - Huawei Cab - MDWS (sadly gone 12/03/18)

jelv

  • Helpful
  • Kitizen
  • *
  • Posts: 1344
Re: VMG1312-B10D new Web GUI 2.0 on V5.13(AAXA.8)C0?
« Reply #32 on: November 04, 2018, 04:07:28 PM »

Doing exactly the same as you I get the ZySH prompt not the # for the BusyBox.

What login are you using?
Logged
Line rental: Pulse8, Broadband: AAISP Home::1 FTTC 80/20, Mobile: id Mobile

tiffy

  • Reg Member
  • ***
  • Posts: 549
Re: VMG1312-B10D new Web GUI 2.0 on V5.13(AAXA.8)C0?
« Reply #33 on: November 04, 2018, 04:39:58 PM »

Code: [Select]
Doing exactly the same as you I get the ZySH prompt not the # for the BusyBox.
Beats me, can't explain, very confusing !

However it works, the tests I have carried out today would seem to confirm that DSLStats won't work with FW revisions later than 5.13(AAXA.5)
Logged
Plusnet 40/10 - DSLStats/RPi - ZyXEL VMG1312-B10A - Huawei Cab - MDWS (sadly gone 12/03/18)

jelv

  • Helpful
  • Kitizen
  • *
  • Posts: 1344
Re: VMG1312-B10D new Web GUI 2.0 on V5.13(AAXA.8)C0?
« Reply #34 on: November 04, 2018, 05:36:08 PM »

After you enter telnet 192.168.1.1 and it prompts for the login do you use "admin" or a different user?
Logged
Line rental: Pulse8, Broadband: AAISP Home::1 FTTC 80/20, Mobile: id Mobile

jelv

  • Helpful
  • Kitizen
  • *
  • Posts: 1344
Confession time
« Reply #35 on: November 04, 2018, 06:04:58 PM »

Something I didn't spot!

On V.5.13(AAXA.7) DSLStats couldn't be used. This is because on telnetting in as admin, instead of the BusyBox you got the ZySH. ? lists the commands available:

Code: [Select]
cfg                                     - DAL command line interface
dns                                     - ZYXEL command line
ethwanctl                               - ZYXEL command line
exit                                    - Close an active terminal session
history                                 - Display or clear CLI history
ifconfig                                - Show network interface configuration
ping                                    - Send ICMP ECHO_REQUEST to network hosts
pppoectl                                - ZYXEL command line
sys                                     - ZYXEL command line
tcpdump                                 - Text based packet capture utility
traceroute                              - monitor each routed node during whole routing path to <host>
vcautohuntctl                           - ZYXEL command line
voicedbgcli                             - ZYXEL command line
wan                                     - ZYXEL command line
wlan                                    - ZYXEL command line
zycli                                   - ZYXEL command line

on V.5.13(AAXA.8) you still get ZySH but the commands available are now this:

Code: [Select]
cfg                                                  - DAL command line interface
dns                                                  - ZYXEL command line
ethwanctl                                            - ZYXEL command line
exit                                                 - Close an active terminal session
history                                              - Display or clear CLI history
ifconfig                                             - Show network interface configuration
ping                                                 - Send ICMP ECHO_REQUEST to network hosts
pppoectl                                             - ZYXEL command line
sys                                                  - ZYXEL command line
tcpdump                                              - Text based packet capture utility
traceroute                                           - monitor each routed node during whole routing path to <host>
vcautohuntctl                                        - ZYXEL command line
voicedbgcli                                          - ZYXEL command line
wan                                                  - ZYXEL command line
wlan                                                 - ZYXEL command line
xdslctl                                              - ZYXEL command line
zycli                                                - ZYXEL command line

Spot the difference?

 :thumbs:
Logged
Line rental: Pulse8, Broadband: AAISP Home::1 FTTC 80/20, Mobile: id Mobile

j0hn

  • Kitizen
  • ****
  • Posts: 2525
Re: VMG1312-B10D new Web GUI 2.0 on V5.13(AAXA.8)C0?
« Reply #36 on: November 04, 2018, 06:57:36 PM »

It was mentioned in an earlier thread that Zyxel were adding back access to the xdslctl commands.

So you simply need to tell DslStats to use the xdslctl command?
Logged
Plusnet FTTC 80/20 -  ECI now Huawei cab
retx low @ 3dB target SNRM
Zyxel VMG1312-B10A bridged with 1508 MTU + Asus RT-AC68U running Asuswrt-Merlin

jelv

  • Helpful
  • Kitizen
  • *
  • Posts: 1344
Re: VMG1312-B10D new Web GUI 2.0 on V5.13(AAXA.8)C0?
« Reply #37 on: November 04, 2018, 07:08:44 PM »

I'd not remembered the post about it being added back.

As DSLStats was working before I upgraded to .7, it just started working without any config changes when I fired it up.
Logged
Line rental: Pulse8, Broadband: AAISP Home::1 FTTC 80/20, Mobile: id Mobile

tiffy

  • Reg Member
  • ***
  • Posts: 549
Re: VMG1312-B10D new Web GUI 2.0 on V5.13(AAXA.8)C0?
« Reply #38 on: November 04, 2018, 07:56:57 PM »

Funny enough, I did notice when re-configuring DSLStats from 1312-B10A to 1312-B10D to test access that choosing the config. paramaters by XyXEL model did change the CLI Command Prefix from "adsl" to "xdslctl", ie. Eric has updated the model parameters, didn't think this was significant at the time.

Don't want to mess about with my RPi 3B (DSLStats) any more to further test access as it's just gone back into service after a memory card failure today, so, are you saying that you can now access DSLStats on revision V.5.12(AAXA.7) & 8 using the "xdslctl" command prefix ?

Still can't explain why I get Busybox login from Win command prompt and you get ZySH prompt when using the same operating system.
I've been logging in as root not admin, could that be the answer ?
Logged
Plusnet 40/10 - DSLStats/RPi - ZyXEL VMG1312-B10A - Huawei Cab - MDWS (sadly gone 12/03/18)

jelv

  • Helpful
  • Kitizen
  • *
  • Posts: 1344
Re: VMG1312-B10D new Web GUI 2.0 on V5.13(AAXA.8)C0?
« Reply #39 on: November 04, 2018, 08:06:42 PM »

Logging in as root will be why you got the BusyBox. How did you get the root password?

xdslctl is available to admin in versions up to 6, not available on 7 and available again on 8 so DSLstats will work on everything but 7 if configured to use the admin login.

If you have a login on 7 that allows the xdslctl command you could configure DSLstats to use that.
Logged
Line rental: Pulse8, Broadband: AAISP Home::1 FTTC 80/20, Mobile: id Mobile

tiffy

  • Reg Member
  • ***
  • Posts: 549
Re: VMG1312-B10D new Web GUI 2.0 on V5.13(AAXA.8)C0?
« Reply #40 on: November 04, 2018, 08:18:56 PM »

Logging in as root will be why you got the BusyBox. How did you get the root password?

xdslctl is available to admin in versions up to 6, not available on 7 and available again on 8 so DSLstats will work on everything but 7 if configured to use the admin login.

If you have a login on 7 that allows the xdslctl command you could configure DSLstats to use that.

Thanks for the additional information.

The recent rather long saga on the supervisor & root PW's is here:
https://forum.kitz.co.uk/index.php/topic,22543.msg385504.html#msg385504

Short answer being, with a lot of help from my friends.
Logged
Plusnet 40/10 - DSLStats/RPi - ZyXEL VMG1312-B10A - Huawei Cab - MDWS (sadly gone 12/03/18)

burakkucat

  • Global Moderator
  • Senior Kitizen
  • *
  • Posts: 26941
  • Over the Rainbow Bridge
    • The ELRepo Project
Re: VMG1312-B10D new Web GUI 2.0 on V5.13(AAXA.8)C0?
« Reply #41 on: November 05, 2018, 12:26:24 AM »

Funny enough, I did notice when re-configuring DSLStats from 1312-B10A to 1312-B10D to test access that choosing the config. paramaters by XyXEL model did change the CLI Command Prefix from "adsl" to "xdslctl", ie. Eric has updated the model parameters, didn't think this was significant at the time.

I recall, from the few months when I used a VMG1312-B10D, that adsl was just a symbolic link to xdslctl and routinely used the latter command.

In fact that is also true for the VMG1312-B10A --

~ # ls -l /bin/adsl
lrwxrwxrwx    1 supervis root             7 Nov 23  2017 /bin/adsl -> xdslctl
~ # ls -l /bin/xdslctl
-rwxr-xr-x    1 supervis root        133748 Nov 23  2017 /bin/xdslctl
~ #


(Colours as seen when viewing the listing output.)
Logged
:cat:  100% Linux and, previously, Unix. Co-founder of the ELRepo Project.

Please consider making a donation to support the running of this site.

jelv

  • Helpful
  • Kitizen
  • *
  • Posts: 1344
Re: VMG1312-B10D new Web GUI 2.0 on V5.13(AAXA.8)C0?
« Reply #42 on: November 05, 2018, 12:29:55 PM »

The upgrade to .8 broke my SIPgate VoIP! Voicemail was fine but on a normal call the person at the other end could hear me but I couldn't hear them.

I struck lucky with the SIPgate help and found this: https://basichelp.sipgate.co.uk/hc/en-gb/articles/204152672

In the router settings under network settings, NAT select the ALG tab. SIP ALG and NAT ALG were turned on. Turning those off fixed the issue.

Logged
Line rental: Pulse8, Broadband: AAISP Home::1 FTTC 80/20, Mobile: id Mobile

tiffy

  • Reg Member
  • ***
  • Posts: 549
Re: VMG1312-B10D new Web GUI 2.0 on V5.13(AAXA.8)C0?
« Reply #43 on: November 05, 2018, 01:46:14 PM »

Interesting, don't currently use VoIP but information noted should the occasion ever arise.

Noted on my on line 1312-B10A that the options are enabled.
Also enabled on my spare 1312-B10D running V.5.13(AAXA.5) FW, would appear to be XyXel default options.
Logged
Plusnet 40/10 - DSLStats/RPi - ZyXEL VMG1312-B10A - Huawei Cab - MDWS (sadly gone 12/03/18)

tiffy

  • Reg Member
  • ***
  • Posts: 549
Re: VMG1312-B10D new Web GUI 2.0 on V5.13(AAXA.8)C0?
« Reply #44 on: November 05, 2018, 04:45:00 PM »

Logging in as root will be why you got the BusyBox. How did you get the root password?

xdslctl is available to admin in versions up to 6, not available on 7 and available again on 8 so DSLstats will work on everything but 7 if configured to use the admin login.

If you have a login on 7 that allows the xdslctl command you could configure DSLstats to use that.

Temporarily changed the 1312-B10D to FW revision V.5.13(AAXA.7) and can confirm that when logging in as "admin" from Windows command prompt I do indeed get the "ZySH" prompt while as already reported, logging in as "root" proceeds to the BusyBox prompt.
At least that clears up the confusion on my part.

Have not yet tried a DSLStats "root" login using either CLI command prefix so can't comment on that at present, will be interesting to see if it does work.
Logged
Plusnet 40/10 - DSLStats/RPi - ZyXEL VMG1312-B10A - Huawei Cab - MDWS (sadly gone 12/03/18)
Pages: 1 2 [3] 4 5