Hi
New to Kitz forum, however have been a reader for a while but only just signed up now (no idea why it took so long). I am also on Thinkbroadband forums too if you do see my username.
Just a quick quick query, unfortunately my line is suffering a bit from I assume some sort of horrendous noise but cannot be certain, as I keep getting these patterns of a lot of CRC, ES, SES and UAS errors all at once it is really odd. It started mostly likely last year November time but wasn't aware that these errors were occurring at that time just speed caps to 18000 and 19999 constantly, as I wasn't using my HG612 then. I then had to make sure the line stayed at 18000 on downstream to avoid the issue with intermittent load of CRC, ES, SES and UAS errors. all was ok for a couple of weeks, then it came back and I had to lower the line speed again to 17000 and it still effecting the line even at that rate. it seems to happen more in the night than in the day, but the other evening was pretty bad. Generally overall i feel my line is getting gradually worse, about year ago got highest INP and delay applied then went down hill from there and now even upstream has INP applied which happened the other week. I am about 1000m from the fibre cab (annoying as there is one 200m away from me) and its a horrible ECI cab I am connected to, hence no G.INP when you see the stats. Wish Openreach would sort that out.
Any one have any idea on the stats below, to me doesn't look good. I really don't want to get an engineer round as the line doesn't loose sync very much so don't think there is a line fault as such so engineer will most likely charge me. Its also intermittent so may not happen when they around. I have spoken to a neighbour who I am good friends with to see if what there fibre is like and their sync is around 14000 downstream so he has similar issues. probably wont be long before DLM caps the speed at 16000 which is nearly have of the max attainable.
BusyBox v1.9.1 (2014-01-21 16:44:38 CST) built-in shell (ash)
Enter 'help' for a list of built-in commands.
# xdslcmd info --stats
xdslcmd: ADSL driver and PHY status
Status: Showtime
Retrain Reason: 1
Last initialization procedure status: 0
Max: Upstream rate = 5321 Kbps, Downstream rate = 30112 Kbps
Bearer: 0, Upstream rate = 5290 Kbps, Downstream rate = 17000 Kbps
Link Power State: L0
Mode: VDSL2 Annex B
VDSL2 Profile: Profile 17a
TPS-TC: PTM Mode(0x0)
Trellis: U:ON /D:ON
Line Status: No Defect
Training Status: Showtime
Down Up
SNR (dB): 11.9 6.1
Attn(dB): 24.6 0.0
Pwr(dBm): 6.0 6.0
VDSL2 framing
Bearer 0
MSGc: 42 33
B: 47 79
M: 1 1
T: 41 45
R: 16 16
S: 0.0896 0.4803
L: 5712 1599
D: 723 67
I: 64 96
N: 64 96
Counters
Bearer 0
OHF: 25484360 420661
OHFErr: 10047 2
RS: 1974141624 2016697
RSCorr: 2877689 8586
RSUnCorr: 316036 0
Bearer 0
HEC: 67227 0
OCD: 5509 0
LCD: 5509 0
Total Cells: 307318173 0
Data Cells: 272609766 0
Drop Cells: 0
Bit Errors: 0 0
ES: 290 690
SES: 139 0
UAS: 252 162
AS: 141009
Bearer 0
INP: 8.00 2.50
INPRein: 0.00 0.00
delay: 16 8
PER: 5.53 16.27
OR: 69.38 19.17
AgR: 17069.32 5309.26
Bitswap: 98118/98156 214/218
Total time = 1 days 22 hours 10 min 49 sec
FEC: 20638214 132564
CRC: 23868 854
ES: 290 690
SES: 139 0
UAS: 252 162
LOS: 1 0
LOF: 8 0
LOM: 0 0
Latest 15 minutes time = 10 min 49 sec
FEC: 1434 0
CRC: 0 0
ES: 0 0
SES: 0 0
UAS: 0 0
LOS: 0 0
LOF: 0 0
LOM: 0 0
Previous 15 minutes time = 15 min 0 sec
FEC: 7895 1
CRC: 0 0
ES: 0 0
SES: 0 0
UAS: 0 0
LOS: 0 0
LOF: 0 0
LOM: 0 0
Latest 1 day time = 22 hours 10 min 49 sec
FEC: 969995 3443
CRC: 2871 2
ES: 21 2
SES: 16 0
UAS: 16 0
LOS: 0 0
LOF: 0 0
LOM: 0 0
Previous 1 day time = 24 hours 0 sec
FEC: 3404081 6470
CRC: 13017 1
ES: 103 1
SES: 78 0
UAS: 71 32
LOS: 0 0
LOF: 0 0
LOM: 0 0
Since Link time = 1 days 15 hours 10 min 35 sec
FEC: 2877689 8586
CRC: 10047 2
ES: 84 2
SES: 61 0
UAS: 27 0
LOS: 0 0
LOF: 0 0
LOM: 0 0
#
I have HG612 modem stats from Ronski, so can run snapshot stats if any one wants to see further stats? Also I am on TalkTalk fibre 40/10 so no quiet line test which is also annoying.
Anyway sorry for long ramble.
Thanks