Kitz ADSL Broadband Information
adsl spacer  
Support this site
Home Broadband ISPs Tech Routers Wiki Forum
 
     
   Compare ISP   Rate your ISP
   Glossary   Glossary
 
Please login or register.

Login with username, password and session length
Advanced search  

News:

Pages: 1 [2]

Author Topic: A little info please  (Read 1249 times)

licquorice

  • Reg Member
  • ***
  • Posts: 839
Re: A little info please
« Reply #15 on: August 22, 2021, 06:08:57 PM »

My only concern is that the wires are the wrong way around but as ive been told here that makes no difference.
all  though i would like it to be as it should.

I read that as one sentence, with the full stop as a comma due to the lower case 'a' hence my reply.  :)

Interesting how different people interpret things differently.  :)
Logged

burakkucat

  • Global Moderator
  • Senior Kitizen
  • *
  • Posts: 33989
  • Over the Rainbow Bridge
    • The ELRepo Project
Re: A little info please
« Reply #16 on: August 22, 2021, 06:40:19 PM »

Interesting how different people interpret things differently.  :)

Yes, indeed.  :)
Logged
:cat:  100% Linux and, previously, Unix. Co-founder of the ELRepo Project.

Please consider making a donation to support the running of this site.

DANNYG

  • Member
  • **
  • Posts: 48
  • Gaming till the end.
Re: A little info please
« Reply #17 on: August 22, 2021, 07:01:25 PM »

I'm sorry for any confusion in my posts im not very well educated.
So i use spell check to try and make sense of the babble i write.
Logged

Alex Atkin UK

  • Kitizen
  • ****
  • Posts: 2969
    • Thinkbroadband Quality Monitors
Re: A little info please
« Reply #18 on: August 22, 2021, 11:29:38 PM »

All i done was clean it all up remove the junction box as it was such a state joined the wires and place them inside a single gang electrical box with a blanking plate for further accesses its a hundred times better than it was.
My only concern is that the wires are the wrong way around but as ive been told here that makes no difference.
all  though i would like it to be as it should.
Many thanks for helping.

How did you join the wires?  As in that case I think its a good idea to get a newer box as suggested so they are joined according to how Openreach would do it.  Would avoid any awkward questions later if you developed a fault.
Logged
INTAKE (ECI) 2xHome Hub 5A (OpenWRT) on Zen & Plusnet, 1xHauwei H122-373 on Three 5G Router: pfSense (i5-7200U) WiFi: nanoHD (OpenWRT) + Honor Router 3
My Broadband History & Ping Quality Monitors

DANNYG

  • Member
  • **
  • Posts: 48
  • Gaming till the end.
Re: A little info please
« Reply #19 on: August 23, 2021, 12:11:04 AM »

I twisted them together.
I will be ordering the box tomorrow.
Logged

DANNYG

  • Member
  • **
  • Posts: 48
  • Gaming till the end.
Re: A little info please
« Reply #20 on: September 10, 2021, 10:02:48 AM »

Hi i received a junction box today could somebody be kind enough to tell what wires go were just out of curiosity while i await bt to fit i have an orange/white  a blue/white and a blue then x2 black copper cables.
Many thanks.
Logged

tubaman

  • Addicted Kitizen
  • *****
  • Posts: 8147
Re: A little info please
« Reply #21 on: September 10, 2021, 12:11:35 PM »

The black pair go under the A and B screw terminals with the orange/white and blue/white on the A and B IDC (punch-down) connectors. The polarity does not matter.
 :)
Logged
BT FTTC 80/20 Huawei Cab - Zyxel VMG8924-B10A

DANNYG

  • Member
  • **
  • Posts: 48
  • Gaming till the end.
Re: A little info please
« Reply #22 on: September 10, 2021, 12:17:05 PM »

thank you.
Logged
Pages: 1 [2]