Print

Please login or register.
1 Hour 1 Day 1 Week 1 Month Forever
Login with username, password and session length

[burakkucat]

Here's a diagram that Kitz has drawn up to show how the modem and the router should be connected.

The HG612 is configured to use the IPv4 address 192.168.1.1 by default. Your router should have a separate IPv4 address in the same sub-net.

Once you have performed the unlocking process, there is no need for the system used to have a static IPv4 address of (say) 192.168.1.100 -- it can be reconfigured as it was prior to the unlocking task.

[jelv]

That's how I'm connected - it must all be fine because as I said, Chrome on the same PC displays the the web interface with no problems. It's something specific to Firefox.

[kitz]

cache? 

[jelv]

Awarded to Kitz!

I've just remembered that when I used the PN supplied sagencom router my VoIP phone was briefly on 192.168.1.1 - must have been something left behind by that - bizarre!

[burakkucat]

It's always the little things that are forgotten which cause the most trouble.    One word from Kitz and all is well . . . 

[kitz]

One word from Kitz and all is well . . . 

If only other things in life was that easy 

[dee.jay]

Hi all,

Sync 65341/20000
Max. Attainable of 77104/22251 SNR 6.3/7.1

So as an update to this. I now have G.INP on my line and it's regularly connecting like this: -

Attainable rate (kbit/s)   76084   19285
Line rate (kbit/s)-------77360    19829

Rather happy with the line rate now being quicker than the attainble!

[kitz]

Rather happy with the line rate now being quicker than the attainble!

Whats your SNRm at?

[dee.jay]

Stats recorded 26 Jun 2015 20:48:24

Code: [Select]

DSLAM/MSAN type:           BDCM:0xa459 / v0xa459
Modem/router firmware:     AnnexA version - A2pv6C038m.d24j
DSL mode:                  VDSL2 Profile 17a
Status:                    Showtime
Uptime:                    6 hours 22 min 15 sec
Resyncs:                   3 (since 25 Jun 2015 12:01:20)
         
            Downstream   Upstream
Line attenuation (dB):     19.0      0.0
Signal attenuation (dB):   Not monitored     
Connection speed (kbps):   76221      19395
SNR margin (dB):           6.1        5.9
Power (dBm):               12.8       7.4
Interleave depth:          8          4
INP:                       48.00      47.00
G.INP:                     Enabled     

RSCorr/RS (%):             0.0677      0.0867
RSUnCorr/RS (%):           0.0000      0.0000
ES/hour:                   0      0

Edit to put data between code tags for better formatting

[kitz]

The reason I asked about your SNRm is because if the line rate is above the attainable rate it usually means the SNRm is running lower than the Target SNRm of 6dB.   If the SNRm falls too low it can cause Errors and eventually cause the line to resync.


However it looks like the line has recently retrained at a rate much nearer to the max attainable.

[dee.jay]

Yes it fell over during the day yesterday and has dropped slightly, but the max attainable has also dropped.

I was running slightly over it at 77360 for nearly a fortnight but I didn't think to make a note of the SNR.

[Alex Atkin UK]

VLAN 301 is used for BT Wifi. To kill BTAgent you have to run the killall -KILL start btagent command

Are you sure about that?  Because I can't see anything on the HG612 that would pass traffic from that VLAN out of LAN1.

Pretty sure that VLAN 301 is just remote provisioning which would indeed be related to BT Agent.