Kitz ADSL Broadband Information
adsl spacer  
Support this site
Home Broadband ISPs Tech Routers Wiki Forum
 
     
   Compare ISP   Rate your ISP
   Glossary   Glossary
 
Please login or register.

Login with username, password and session length
Advanced search  

News:

Pages: 1 2 3 [4] 5 6 ... 26

Author Topic: OpenWrt (Chaos Calmer r46559) for ECI/r v1 & v2 - Update: G.INP/ReTX Support  (Read 288072 times)

jsamuel

  • Reg Member
  • ***
  • Posts: 117

Panic over!  :D
The next time you want to flash an image, just setup tftp and run "run update_openwrt" and "reset" since the variables are now saved.
Yes, it can be undone but by "bricking it" i mean OpenWrt will boot, but your ethernet ports won't work and you'll need to dabble with the serial again to fix it. The v2 image vs v1 has just a phy driver change :)
Logged

jsamuel

  • Reg Member
  • ***
  • Posts: 117

Quote
Line Mode: G.993.2 (VDSL2) — Annex B — Profile 17a
Status & Uptime: UP — 2h 43m 14s
Line State: showtime_tc_sync [0x801]
Power Mode: L0 - Synchronized
DSLAM/MSAN VID: IFTN

Alignment: Downstream — Upstream

Attainable Line Speed: 100.285 Mb/s — 22.225 Mb/s
Actual Line Speed: 48.994 Mb/s — 11.993 Mb/s
Trellis: D: ON — U: ON
Bitswap: D: OFF — U: OFF
G.INP: D: Not Enabled — U: Not Available
Virtual Noise Support: D: Not Supported — U: Not Supported
Interleave Depth: 1 — 381
Interleave Block: 255 — 32
Interleave Delay: 0ms — 4ms
NFEC: 255 — 32
RFEC: 16 — 16
LSYMB: 13147 — 6096
LPATH: 0 — 0
INP: 0.0 — 4.0
Line Attenuation: 9.0 dB — 10.3 dB
Noise Margin/SNR: 20.7 dB — 13.1 dB
Transmit Power: -2.-3 dB — 12.6 dB

Errors

ES: 0 — 1
SES: 0 — 0
UAS: 0 — 1
FEC: 0 — 214
CRC_P: 0 — 0
CRCP_P: 0 — 0

Hopefully DLM removes the cap on my IP profile soon as I have yet to test the throughput. I really wish we could disable this rubbish for situations like hardware testing!
Logged

GigabitEthernet

  • Kitizen
  • ****
  • Posts: 2243

All setup - unfortunately syncing about 7Mb lower than my Billion 8800NL.

How would I configure the ECI to act as a router as well as a modem? :)
Logged

jsamuel

  • Reg Member
  • ***
  • Posts: 117

All setup - unfortunately syncing about 7Mb lower than my Billion 8800NL.

How would I configure the ECI to act as a router as well as a modem? :)
Hopefully within time it might sort itself out :)

You can connect LAN2 and use it that way, though it requires you set a static IP. If you want DHCP re-enabled,
login via SSH and nano /etc/config/dhcp

Change
Quote
config dhcp 'lan'
   option interface 'lan'
   option ignore '1'
to something like
Quote
config dhcp 'lan'
   option 'interface'   'lan'
   option 'start'       '100'
   option 'limit'        '150'
   option 'leasetime'   '12h'
        option ra server
        option dhcpv6 server
and
Quote
/etc/init.d/dhcp restart
« Last Edit: August 15, 2015, 03:10:52 PM by jsamuel »
Logged

GigabitEthernet

  • Kitizen
  • ****
  • Posts: 2243

Oh is there an adjustment period when you change the chipset? I've only ever used Broadcom so I've never had a chance to test it.

I had interleaving reduced to a depth of 1 on the upstream today so I've got a couple of Mb back but the ECI is still 2Mb slower than the Broadcom modems I've used :(

So the way you've described will allow me to plug a device into LAN2 and Internet will work via this port?
Logged

jsamuel

  • Reg Member
  • ***
  • Posts: 117

There is I believe, and the DSLAM might resync and realize the CPE has a different chipset but I don't know. Or it could be that you've switched the modems too quickly and the DSLAM has lowered it a tad, but will fix itself.

Sorry, lack of sleep  :-[
The way I've set it up by default is LAN1 > Router WAN, LAN2 > Router LAN.

I assume the way you want it setup is
LAN1 > Router WAN
LAN2 > PC?

That configuration _should_ work out of the box too.
Logged

GigabitEthernet

  • Kitizen
  • ****
  • Posts: 2243

Well actually I wanted both ports to go to a PC :)
Logged

VDSL2User

  • Member
  • **
  • Posts: 31

I think I have killed my ECI /r V 1.1 attempting to install OpenWRT
I had an old spare ECI which I had attached the UART header to some time ago.
Well i ran all the instructions up to and including the run update_openwrt but when this
got to the copy to flash part it just kept coming up with something about protected
At this stage I thought that if I had any issues I would be able to use UBoot and try again
so I went ahead and did the reset as I could think of no other way to get past the issue.
Now I can get UBoot but there is no images in the flash as I guess the erase command from the
update_openwrt has wiped them (just get bad magic number messages)
Problem is I don't appear to be able to get the VR9 switch to operate anymore, no lights when ping etc
and cable disconnected on the laptop. Tried alternate RJ45 cables but no joy.
Am I correct in thinking that UBoot does is not enough environment to actually use the VR9 switch ports native?
When I try a ping it says using VR9 Switch device and then a while later comes up with host is not alive
(no lights on the LAN port come on).
Oh well you win some and you lose some ..... it was only a cheap spare that I never use as I have 2 HG612's
and a Billion 8800NL for connection, just liked OpenWRT which I ran on the homehub 2 some years back with ADSL.
Logged

GigabitEthernet

  • Kitizen
  • ****
  • Posts: 2243

When you turn on the ECI modem with the UART connected, what do you see?

Could you post the output?
Logged

VDSL2User

  • Member
  • **
  • Posts: 31

Well I found I had another ECI modem hiding away in the cupboard, this one a V 1.2
It also had a header from UART in place as I had looked at an unlock some time ago.
So off I went with all the instructions again (remembering to use the V2 test image this time)
and hey presto it has worked and I now have OpenWRT running.
Now the new setup has the modem on IP address 192.168.1.1 which clashes with my ASUS RT-AC87U router
I can see the WAN bridge and LAN settings page (when plugged into LAN 2 with a static of 192.168.1.100
on the laptop) but not sure how to best change this to say 192.168.2.1
I could change the ASUS to operate on the 192.168.2.x subnet I guess as an alternate option.
At present I have an additional interface on the ASUS eth0.1 which uses 192.168.2.253 and an IPTABLES
command to route all traffic for this subnet down the WAN link allowing me to access the router (HG612) via a single
cable running both PPPoE and LAN. The HG612 is on address 192.168.2.254 and has the PPPoE vlan unbound from
LAN port 1.
Can the ECI with OpenWRT be made to operate in the same way ?
I plan to try the ECI on the line tomorrow (I am on a Huawei cab with G.Inp enabled so can see if it is picked up ok)

Just spotted your reply AlecR while creating the above post .....
Then other (broken) ECI displays the following at startup

ROM VER: 1.0.5
CFG 01
DDR Access auto data-eye tuning Rev 0.3a
DDR size from 0xa0000000 - 0xa1ffffff
DDR check ok... start booting...



U-Boot 1.0.4 (Oct 18 2010 - 16:20:02)

CLOCK CPU 333M RAM 166M
DRAM:  32 MB

 relocate_code start
 relocate_code finish.

FLASH MANUFACT: c2

FLASH DEVICEID: cb
Flash:  8 MB
*** Warning - bad CRC, using default environment

In:    serial
Out:   serial
Err:   serial
Net:   fw_addr=0xa0200000
Internal phy(FE) firmware version: 0xffff
vr9 Switch

Type "run flash_flash" to mount root filesystem over flash

Hit 'Esc' key to stop autoboot:  0
## Booting image from active region 1 at 80800000 ...
Check RSA image magicBad Magic Number
Retry another region
## Booting image from active region 2 at b03f0000 ...
Check RSA image magicBad Magic Number
VR9 #
VR9 # ping 192.168.1.100
Using vr9 Switch device
ping failed; host 192.168.1.100 is not alive
VR9 #
Logged

GigabitEthernet

  • Kitizen
  • ****
  • Posts: 2243

So you can't type anything next to VR9 #?
Logged

VDSL2User

  • Member
  • **
  • Posts: 31

Yes I can type anything , above I tried a ping 192.168.1.100 (the laptop connected to LAN1 port)
but no port lights (amber or green) and a cable disconnected showing on laptop then router
gives not alive response after about 15-20 seconds.
Logged

GigabitEthernet

  • Kitizen
  • ****
  • Posts: 2243

Then you should be able to follow the instructions to flash OpenWRT again and it should work perfectly :)
Logged

VDSL2User

  • Member
  • **
  • Posts: 31

I have tried a couple of times but with the LAN link down the TFTP never
connects and downloads the image, it just keeps displaying T T T T then
times out and repeats over and over.
I will have another go at it tomorrow but now I have a working V1.2 ECI I am
less bothered about the V1.1 broken one (I think something may have gone
on the electronics to the LAN ports that just happened to be at the same time I was
working on the device.
Logged

GigabitEthernet

  • Kitizen
  • ****
  • Posts: 2243

I believe you might have flashed the V2 image on the V1 as previously jsamuel said the ethernet ports not working was a symptom of this :)

He also said it should be recoverable so I suspect he can provide assistance soon :)
Logged
Pages: 1 2 3 [4] 5 6 ... 26
 

anything