Hi
I come across this on my pastebin and i tried to find it over the internet but i couldn't
so here it is for anyone who wants to use there BT HomeHub 2.0 Type B as a cable router, If your going to use it on a existing router, you need to keep it away from 192.168.1.0/24 as they will clash! Also
Don't forget Port 4 is for
WAN with the following commands in KiTTY but PuTTY should be ok.
From what i can remember the DNS servers are auto set and there no interception about the ADSL been down
conf set dev/eth1/type switch_port_dev
conf set dev/eth1/logical_network 1
conf set dev/eth1/is_sync 0
conf set dev/eth1/enabled 1
conf set dev/eth1/is_physical 1
conf set dev/eth1/switch_port 4
conf set dev/eth1/depend_on_name eth0
conf set dev/eth1/route_level 4
conf set dev/eth1/metric 3
conf set dev/eth1/mtu_mode 1
conf set dev/eth1/default_route 1
conf set dev/eth1/has_ip 1
conf set dev/eth1/is_wan_man 1
conf set dev/eth1/is_wan_data 1
conf set dev/eth1/is_dns_neg 1
conf set dev/eth1/password cb4694fcd1492e95a9d56e39982e361b
conf set dev/eth1/encryption/key cb4694fcd1492e95a9d56e39982e361b
conf set dev/eth1/rip/enabled 0
conf set dev/eth1/rip/input_version 3
conf set dev/eth1/rip/output_version 2
conf set dev/eth1/ipv6/0/addr fec0:0:0:3::
conf set dev/eth1/ipv6/0/prefix_len 64
conf set dev/eth1/ipv6/0/is_eui64 1
conf set dev/eth1/is_fastpath_enabled 1
conf set dev/eth1/description "WAN Ethernet"
conf set dev/eth1/mgt_dev 1
conf set dev/eth1/qos/shaping/bandwidth_fixup_percent 105
conf set dev/eth1/mcast/igmp_proxy_default 1
conf set dev/eth1/mcast/version 3
conf set dev/eth1/id 98
conf set dev/eth1/alias WANPORT
conf set dev/eth1/dhcps lease
conf set dev/ppp1/enabled 1
conf set dev/ppp1/logical_network 1
conf set dev/ppp1/type pppoe
conf set dev/ppp1/has_ip 1
conf set dev/ppp1/is_sync 0
conf set dev/ppp1/is_dns_neg 1
conf set dev/ppp1/mtu_mode 1
conf set dev/ppp1/default_route 1
conf set dev/ppp1/route_level 4
conf set dev/ppp1/is_trusted 0
conf set dev/ppp1/mcast/igmp_proxy_default 1
conf set dev/ppp1/mcast/version 3
conf set dev/ppp1/username bthomehub@btbroadband.com
conf set dev/ppp1/depend_on_name eth1
conf set dev/ppp1/logical_depend_on eth1
conf set dev/ppp1/ppp/auth/pap 1
conf set dev/ppp1/ppp/auth/chap 1
conf set dev/ppp1/ppp/auth/ms_chap_v1 1
conf set dev/ppp1/ppp/auth/ms_chap_v2 1
conf set dev/ppp1/ppp/reconnect_time 30
conf set dev/ppp1/max_idle 1200
conf set dev/ppp1/atm/pvc/0/vpi 0
conf set dev/ppp1/atm/pvc/0/vci 38
conf set dev/ppp1/atm/encaps 1
conf set dev/ppp1/is_fastpath_enabled 1
conf set dev/ppp1/id 99
conf set dev/ppp1/description "WAN PPPoE"
conf set dev/ppp1/alias ""
conf set dev/ppp1/dhcps lease
conf set dev/eth1/route/failover/enabled 1
conf set dev/eth1/route/failover/rollover 0
conf set dev/ppp0/route/failover/enabled 1
conf set dev/ppp0/route/failover/rollover 1
conf set dev/ppp1/route/failover/enabled 1
conf set dev/ppp1/route/failover/rollover 1
conf set route/failover/enabled 1
conf set system/network/http_interception 0
conf set system/network/net_config_http_interception 0
conf set system/network/initial_setup 0
