Print

Please login or register.
1 Hour 1 Day 1 Week 1 Month Forever
Login with username, password and session length

[BritBrat]

The section that controls all the cabinets in the Southwest (Bristol) did it 

He phoned to check out stats.

[NewtronStar]

Router just resynced:

3. Firmware version: Software version 4.7.5.1.83.8.173.1.4 (Type A) Last updated Unknown
4. Board version: BT Hub 5A
5. VDSL uptime: 0 days, 00:09:26
6. Data rate: 8838 / 60027
7. Maximum data rate: 8841 / 60320
8. Noise margin: 6.1 / 6.1
9. Line attenuation: 0.0 / 22.6
10. Signal attenuation: 0.0 / 20.9

I will leave it alone and put the modem back on tomorrow.

It will resync if you keep changing from the HH5 and back to HG612, if you want the DLM to settle down then I would advise you to keep either modem active for 14 days on your line, going back and forth is not good even if it is a 24 hour period.

the DLM on FTTC needs to see a stable connection for 14 to 28 days.

[BritBrat]

OK thanks, will do.

[BritBrat]

I think my speed may drop soon and again why are my actual speeds faster than my line speeds?

3. Firmware version: Software version 4.7.5.1.83.8.173.1.4 (Type A) Last updated Unknown
4. Board version: BT Hub 5A
5. VDSL uptime: 0 days, 14:07:34
6. Data rate: 8871 / 60941
7. Maximum data rate: 8529 / 60183
8. Noise margin: 5.7 / 5.5
9. Line attenuation: 0.0 / 22.6
10. Signal attenuation: 0.0 / 21.0

[NewtronStar]

I think my speed may drop soon and again why are my actual speeds faster than my line speeds?

3. Firmware version: Software version 4.7.5.1.83.8.173.1.4 (Type A) Last updated Unknown
4. Board version: BT Hub 5A
5. VDSL uptime: 0 days, 14:07:34
6. Data rate: 8871 / 60941
7. Maximum data rate: 8529 / 60183
8. Noise margin: 5.7 / 5.5
9. Line attenuation: 0.0 / 22.6
10. Signal attenuation: 0.0 / 21.0

I have seen on many occassions were my Upload attainable rate has been lower than the Upload line rate it and it stayed like for a few weeks, until a retrain 0 came in and it went back to normal
(Attainable Rate higher than the line rate) it only seems to happen on the Upload never Download,
and I don't know why this happens but it does from time to time.

What I would have done is use the unlocked HG612 as the modem and Connect HH5 and use it as a router, you may be doing this  connect Wan port on HH5 to Hg612 Lan1 and lan cable from Lan2 (HG612) to any lan ports on the HH5 and you can access them both, all I have is HG612 and a HH3 and it works fine.

you need to get as much stats as you can over many weeks to see how your line is holding up.

[Bald_Eagle1]

I think my speed may drop soon and again why are my actual speeds faster than my line speeds?

By actual speeds, do you mean throughput?

Sync speed = line rate = Bearer (or Path).
Max rate (from a HG612) = Attainable rate.

From my HG612:-

Max:   Upstream rate = 4946 Kbps, Downstream rate = 22496 Kbps
Bearer:   0, Upstream rate = 4928 Kbps, Downstream rate = 20488 Kbps

My Max (attainable) rates are higher than my Bearer (sync speeds).

Also:-

                Down      Up
SNR (dB):  5.6       6.2


Occasionally, when a connection syncs at very close to attainable rates (when SNRM is around the target 6dB), attainable rates can end up lower than sync speeds when SNRM lowers, usually in the evenings.

It may be worth rechecking between noon & 14:00, when SNRM is usually at its highest level.

[BritBrat]

Just loging todays result:

Again a reset at 4:00am.

3. Firmware version: Software version 4.7.5.1.83.8.173.1.4 (Type A) Last updated Unknown
4. Board version: BT Hub 5A
5. VDSL uptime: 1 days, 03:29:51
6. Data rate: 8871 / 60941
7. Maximum data rate: 8443 / 61215
8. Noise margin: 5.7 / 6.1
9. Line attenuation: 0.0 / 22.6
10. Signal attenuation: 0.0 / 21.0

[Ronski]

Well your sync speeds are looking much better now, and close to the attainable speeds.