Kitz Forum
Broadband Related => Broadband Hardware => Topic started by: SaltyWagyu on May 15, 2017, 12:07:42 PM
-
Just bought my Vigor 130 after finding out I'm on an ECI cabinet, unfortunately got less than expected sync increase over the Zyxel VMG-1312 (broadcom), 71,229 to 72,728. But anyway I'm planning to keep it and wait for G.IMP to reach my cabinet.
I have a few questions about the user interface. It's currently bridged to my ASUS RT-AC87U and can access the Vigor 130 UI via this guide (https://github.com/RMerl/asuswrt-merlin/wiki/Access-modem-Web-UI-on-WAN-port-(no-script)). The time and date is wrong, my Zyxel was similar when it was changed to bridge mode, except it was 2 months behind. Is wrong date+time a common thing on bridged modems?
It's showing VDSL as disconnected (see attachment) although everything is running fine, normal? Where can I find connection uptime? vdsl status in the console does not show it either.
> vdsl status
---------------------- ATU-R Info (hw: annex A, f/w: annex A/B/C) -----------
Running Mode : 17A State : SHOWTIME
DS Actual Rate : 72728000 bps US Actual Rate : 20000000 bps
DS Attainable Rate : 73164840 bps US Attainable Rate : 24729066 bps
DS Path Mode : Fast US Path Mode : Fast
DS Interleave Depth : 1 US Interleave Depth : 1
NE Current Attenuation : 10 dB Cur SNR Margin : 6 dB
DS actual PSD : -1.-8 dB US actual PSD : -1.-7 dB
NE CRC Count : 21 FE CRC Count : 1949
NE ES Count : 2 FE ES Count : 1775
Xdsl Reset Times : 0 Xdsl Link Times : 1
ITU Version[0] : b5004946 ITU Version[1] : 544e0000
VDSL Firmware Version : 05-07-06-0D-01-07 [with Vectoring support]
Power Management Mode : DSL_G997_PMS_L0
Test Mode : DISABLE
-------------------------------- ATU-C Info ---------------------------------
Far Current Attenuation : 9 dB Far SNR Margin : 9 dB
CO ITU Version[0] : b5004946 CO ITU Version[1] : 544eb206
DSLAM CHIPSET VENDOR : < IFTN >
-
The system uptime is on the second image. Your vigor says: System Up Time 21:48:56. If the xdsl link times (from vdsl status) is 1 then the uptime is also 21:48:56
I note you are not on the latest Vigor 130 firmware version, 3.8.1BT is out
Also I would recommend this firmware for your Asus: https://asuswrt.lostrealm.ca
-
Thanks for your reply, but I'm looking for VDSL uptime, which is different from how long the modem has been powered on for.
I have seen the new firmware update but the only change is 1. Resolved an issue with the “show adsl” telnet command so did not consider it important to update.
I am using latest Asuswrt Merlin firmware :)
-
After some nosing around the terminal:
vdsl status counts - will tell you the uptime in seconds ;D
And it includes some handy 15min/daily stats:
Type ? for command help
> vdsl status counts
[ Counters: Showtime ]
Near End Far End Note
ElapsedTime : 975209 975209 (seconds)
CRC : 498 2949
FEC : 32749 34547
HEC : 0 0
CRC_P : 157 0
CRCP_P : 0 0
CVP_P : 0 0
NCD : 0 0
LCD : 0 0
ES : 408 1639
SES : 0 11
LOSS : 0 493
UAS : 0 0
LOFS : 0 0
[ Counters: 15Min ]
Near End Far End Note
ElapsedTime : 847 847 (seconds)
CRC : 0 2
FEC : 0 3
HEC : 0 0
CRC_P : 0 0
CRCP_P : 0 0
CVP_P : 0 0
NCD : 0 0
LCD : 0 0
ES : 0 1
SES : 0 0
LOSS : 0 0
UAS : 0 0
LOFS : 0 0
[ Counters: 1DAY ]
Near End Far End Note
ElapsedTime : 80947 80947 (seconds)
CRC : 27 6
FEC : 999 34
HEC : 0 0
CRC_P : 6 0
CRCP_P : 0 0
CVP_P : 0 0
NCD : 0 0
LCD : 0 0
ES : 25 5
SES : 0 0
LOSS : 0 0
UAS : 0 0
LOFS : 0 0
-
Hi,
I realise the last post was a few months ago now, but I'm trying to figure out which of the values from the vdsl status counts indicates the xDSL sync time. If I look at my modem / system uptime from show status I see 622:0:28 (hh:mm:ss).
> show status
System Uptime:622:0:28
LAN Status
Primary DNS:8.8.8.8 Secondary DNS:8.8.4.4
IP Address:192.168.255.10 Tx Rate:298836061 Rx Rate:471630364
WAN 1 Status: Disconnected
Enable:Yes Line:xDSL Name:
Mode:PPPoE Up Time:0:00:00 IP:--- GW IP:---
TX Packets:0 TX Rate:0 RX Packets:0 RX Rate:0
WAN 2 Status: Disconnected
Enable:Yes Line:Ethernet Name:
Mode:--- Up Time:0:00:00 IP:--- GW IP:---
TX Packets:0 TX Rate:0 RX Packets:0 RX Rate:0
VDSL Information: VDSL Firmware Version:05-07-06-0D-01-07
Mode:17A State:SHOWTIME TX Block:0 RX Block:0
Corrected Blocks:12057 Uncorrected Blocks:470
UP Speed:14292000 Down Speed:50222000 SNR Margin:2 Loop Att.:21
I found the sys diag_log log command useful to see what's happening on the xDSL and from this I can see the last time the line state changed was roughly 596:51:30 since the modem was booted. The exact uptime when the line last changed from "Train(6) to Showtime(7)" was 596:52:08.
596:51:33 [DSL] Line state has changed: 00000801 -> 00000860
596:51:33 [DSL] Status was switched: Showtime(7) to ShutDownWait(15)
596:51:33 [DSL] Line state has changed: 00000860 -> 00000001
596:51:33 [DSL] Status was switched: ShutDownWait(15) to ShutDownReached(16)
596:51:33 [DSL] Status was switched: ShutDownReached(16) to Exception(8)
596:51:33 [DSL] Training Exception:DSL autoboot exception!! exception cnt:1
596:51:35 [DSL] Status: DSL line down by exception
596:51:35 [DSL] Status was switched: Exception(8) to Restart(10)
596:51:35 [DSL] Line state has changed: 00000001 -> 00000000
596:51:35 [DSL] Status was switched: Restart(10) to FirmwareRequest(1)
596:51:35 [DSL] Line state has changed: 00000000 -> 000000FF
596:51:35 [DSL] Training Exception Workaround: reload the same modem code
596:51:35 [DSL] Entering VDSL2 mode
596:51:35 [DSL] modem code: [05-07-06-0D-01-07]
596:51:35 [DSL] Status was switched: FirmwareRequest(1) to firmwareReady(3)
596:51:36 [DSL] Line state has changed: 000000FF -> 00000100
596:51:36 [DSL] Status was switched: firmwareReady(3) to Init(5)
596:51:36 [DSL] >> nXtseA=0d, nXtseB=00, nXtseV=07, nFwFeatures=9
596:51:36 [DSL] >> nHsToneGroupMode=0, nHsToneGroup=102, nToneSet=3, nCamState=2
596:51:36 [DSL] Enable BT related fixes.
596:51:36 [DSL] dms 549 0 2 240B 0.
596:51:36 [DSL] Line state has changed: 00000100 -> 00000100
596:51:36 [DSL] Line state has changed: 00000100 -> 00000200
596:51:36 [DSL] Status was switched: Init(5) to Train(6)
596:51:39 [DSL] Line state has changed: 00000200 -> 00000300
596:51:42 [DSL] Line state has changed: 00000300 -> 00000380
596:52:06 [DSL] Line state has changed: 00000380 -> 00000801
596:52:07 [DSL] Record last show time mode: VDSL2
596:52:08 [DSL] Status was switched: Train(6) to Showtime(7)
596:52:09 [DSL] ActualNetDataRateUs=14292000, ActualNetDataRateDs=50222000
596:52:09 [DSL] VDSL2: UP rate=0, DOWN rate=47983 Kbps, Mode=17A
596:52:09 [DSL] G.Vectoring Status: OFF
596:52:21 [DSL] CPE Inventory:
596:52:21 [DSL] G994VendorID: B5 00 49 46 54 4E 00 00
596:52:21 [DSL] SystemVendorID: B5 00 49 46 54 4E 00 00
596:52:21 [DSL] VersionNumber: 33 2E 38 2E 31 2E 32 5F 42 54 00 00 00 00 00 00
596:52:21 [DSL] SerialNumber: 30 30 31 64 61 61 38 64 61 65 36 63 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
596:52:21 [DSL] XTSECapabilities: 00 00 00 00 00 00 00 07
596:52:21 [DSL] CO Inventory:
596:52:21 [DSL] G994VendorID: B5 00 42 44 43 4D A4 8C
596:52:21 [DSL] SystemVendorID: B5 00 42 44 43 4D 00 00
596:52:21 [DSL] VersionNumber: 76 31 30 2E 30 39 2E 31 32 20 20 20 20 20 20 00
596:52:21 [DSL] SerialNumber: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
596:52:21 [DSL] XTSECapabilities: 00 00 00 00 00 00 00 00
So if I convert the 622:00:28 to seconds (2,239,228) and subtract 596:52:08 (2,148,728) from it I get 90,500 seconds. But when I look at the numbers from the vdsl status counts command I don't see anything that matches.
> vdsl status counts
[ Counters: Showtime ]
Near End Far End Note
ElapsedTime : 1920487 1920487 (seconds)
CRC : 442 12057
FEC : 0 249413
HEC : 0 0
CRC_P : 29 0
CRCP_P : 0 0
CVP_P : 0 0
NCD : 0 0
LCD : 0 0
ES : 110 11366
SES : 18 56
LOSS : 1 7
UAS : 0 0
LOFS : 0 0
[ Counters: 15Min ]
Near End Far End Note
ElapsedTime : 26 26 (seconds)
CRC : 0 0
FEC : 0 9
HEC : 0 0
CRC_P : 0 0
CRCP_P : 0 0
CVP_P : 0 0
NCD : 0 0
LCD : 0 0
ES : 0 0
SES : 0 0
LOSS : 0 0
UAS : 0 0
LOFS : 0 0
[ Counters: 1DAY ]
Near End Far End Note
ElapsedTime : 79226 79226 (seconds)
CRC : 449 14
FEC : 0 11414
HEC : 0 0
CRC_P : 32 0
CRCP_P : 0 0
CVP_P : 0 0
NCD : 0 0
LCD : 0 0
ES : 134 1
SES : 29 0
LOSS : 0 0
UAS : 0 0
LOFS : 0 0
Am I missing something here?
Regards