Print

Please login or register.
1 Hour 1 Day 1 Week 1 Month Forever
Login with username, password and session length

[les-70]

 With 1.06t firmware please could you try a "xdslcmd info --version" command on telnet and report the outcome.  Also the outcome from xdslcmd on its own.  I am interested to see if there are any dsl driver changes.

[kitzuser87430]

any dsl driver changes.

Still A2pv6F039e

will post more info when using my windows laptop sometime.

Ian

[les-70]

   Thanks for that.  I guess the xdslcmd on its own will show the same options but it would be good to try it sometime.  It may be possible to have updated options available even if the driver version has not changed.

[phi2008]

Does the HG635 support bridge mode?

[kitzuser87430]

Does the HG635 support bridge mode?

Yes

My spare hg635 recieved the update to firmware v 1.06 this afternoon, this router was on the open source software (HG635v1.04t_multicast_with_multicfg_main.bin) the only thing i changed was the "Connection request username:" from the default (userid) to the tt firmware setting of cpeuser.

Ian

[broadstairs]

My HG635 got updated this morning and caused me a whole load of grief. My wife's laptop would not connect to the internet and eventually after digging into W8.1 for ages I eventually found that the DHCP server part of the HG635 setup needed re-doing as it was not providing gateway and dns addresses, and once saved everything started up OK. NOT impressed - this should NOT happen.

One thing I have done it to get the help info for the xdslcmd from the f/w  as here:-

Code: [Select]

$ xdslcmd --help
Usage: xdslcmd start [--up] [--mod <a|d|l|t|2|p|e|m|v>] [--lpair <(i)nner|(o)uter>]
           [--trellis <on|off>] [--snr <snrQ4>] [--bitswap <on|off>] [--sesdrop <on|off>]
           [--sra <on|off>] [--CoMinMgn <on|off>] [--i24k <on|off>] [--phyReXmt <0xBitMap-UsDs>]
           [--TpsTc <0xBitMap-AvPvAaPa>] [--monitorTone <on|off>]
           [--profile <0x00 - 0xFF>|<"8a |8b |8c |8d |12a |12b |17a |30a">] [--us0 <on|off>]
           [--dynamicD <on|off>] [--dynamicF <on|off>] [--SOS <on|off>]
           [--forceJ43 <on|off>] [--toggleJ43B43 <on|off>]
       xdslcmd stop
       xdslcmd connection [--up] [--down] [--loopback] [--reverb]
           [--medley] [--noretrain] [--L3] [--diagmode] [--L0]
           [--tones] [--normal] [--freezeReverb] [--freezeMedley]
       xdslcmd configure [--mod <a|d|l|t|2|p|e|m|v>] [--lpair <(i)nner|(o)uter>]
           [--trellis <on|off>] [--snr <snrQ4>] [--bitswap <on|off>] [--sesdrop <on|off>]
           [--sra <on|off>] [--CoMinMgn <on|off>] [--i24k <on|off>] [--phyReXmt <0xBitMap-UsDs>]
           [--TpsTc <0xBitMap-AvPvAaPa>] [--monitorTone <on|off>]
           [--profile <0x00 - 0xFF>|<"8a |8b |8c |8d |12a |12b |17a |30a">] [--us0 <on|off>]
           [--dynamicD <on|off>] [--dynamicF <on|off>] [--SOS <on|off>]
           [--forceJ43 <on|off>] [--toggleJ43B43 <on|off>]
       xdslcmd bert [--start <#seconds>] [--stop] [--show]
       xdslcmd afelb [--time <sec>] [--tones] [--signal <1/2/8>]
       xdslcmd qlnmntr [--time <sec>] [--freq <msec>]
       xdslcmd inm [--start <BB_THRESH 10*dB> <INMIATO> <INMIATS>] [--stop] [--show]
       xdslcmd snrclamp [--shape <shapeId>] [--bpshape [bpIndex-bpLevel,]]
       xdslcmd diag [--logstart <nBytes>] [--logpause] [--logstop] [--loguntilbufferfull <nBytes>]
           [--loguntilretrain <nBytes>]
       xdslcmd info [--state] [--show] [--stats] [--SNR] [--QLN] [--Hlog] [--Hlin] [--HlinS] [--Bits]
           [--24hrhiststat]
           [--pbParams] [--linediag] [--linediag1] [--vdsllinediag] [--adsllinediag] [--total] [--testparam]
           [--toneGroupObjects][--reset] [--vendor] [--cfg]
       xdslcmd profile [--show] [--save] [--restore]
       xdslcmd --version
       xdslcmd --help

as I believe someone wanted to see it. At least the telnet access and I think everything else worked apart from DHCP.

Stuart

[broadstairs]

This morning I have been put back on fastpath. The issue is that I guess the router probably done a re-sync because my DHCP manual DNS server settings have been wiped out again meaning nothing gets any DNS server addresses if they are on automatic, fixed IPs are OK. I will report this to TT today.

Stuart

[npr]

I had the same issue of custom dns settings in DHCP being regularly lost with the old v1.04t firmware. I was hoping this issue would be fixed with new firmware.
Doesn't cause a resync though. 

Still waiting for the upgrade here, anyone know if remote management needs to be enabled for this to happen ?

[les-70]

I don't "know" but the TR069 connection and remote mange management would normally both need to enabled.  Make sure you do a shields up if you make those changes with one of the old configs.  They are already enabled in the newer ones. 

[les-70]

   My HG635 updated as soon as it was swapped in today - from the version in the opensource distribution.  Not impressed.  At 1m seems 1.06 seems to have taken about 5mb/s off both 2.4 and 5g throughput plus gaining a number of niggles reported elsewhere.  Nothing positive as far as I can tell.

[phi2008]

My HG635 got updated this morning and caused me a whole load of grief.

I switched over to TalkTalk today and also had issues. Had my HG635 connected waiting for TalkTalk to migrate me over and was using WiFi, almost as soon as the connection went live I lost and could not regain WiFi connectivity - resorted to a factory reset in the end and found it had been updated to 1.06t. 

[npr]

I enabled TR069 last week but haven't received the update yet. I'll enable remote management now and see how long it takes.

Update:
Updated to v1.06t within about 3 minutes of enabling remote management.

The update process did cause a resync.

Routers Log report:
20:20:06 03/12/2014   System   Warning   Reboot from the WAN side.
20:20:06 03/12/2014   System   Notice   Upgrading finished: cwmp.
20:19:37 03/12/2014   User Level   Notice   CWMP:Cwmp post inform success.
20:19:37 03/12/2014   System   Warning   Upgrading beginning.

Edit 2:
The pinhole reset button is not working after the FW update.

After doing a factory reset through the GUI, telnet no longer works.

Also had the following hacking attempt.

20:51:45 03/12/2014    User Level    Notice    User sh login fail by telnet 186.223.109.178.
20:51:03 03/12/2014    User Level    Notice    User root login fail by telnet 186.223.109.178.
20:50:25 03/12/2014    User Level    Notice    User root login fail by telnet 186.223.109.178.
20:49:45 03/12/2014    User Level    Notice    User root login fail by telnet 186.223.109.178.
20:49:06 03/12/2014    User Level    Notice    User root login fail by telnet 186.223.109.178.
20:48:26 03/12/2014    User Level    Notice    User root login fail by telnet 186.223.109.178.
20:47:47 03/12/2014    User Level    Notice    User root login fail by telnet 186.223.109.178.
20:47:08 03/12/2014    User Level    Notice    User root login fail by telnet 186.223.109.178.
20:46:28 03/12/2014    User Level    Notice    User root login fail by telnet 186.223.109.178.
20:45:49 03/12/2014    User Level    Notice    User root login fail by telnet 186.223.109.178.
20:45:10 03/12/2014    User Level    Notice    User root login fail by telnet 186.223.109.178.
20:44:30 03/12/2014    User Level    Notice    User root login fail by telnet 186.223.109.178.
20:44:02 03/12/2014    User Level    Notice    User admin login from 192.168.1.2 successfully.
20:43:51 03/12/2014    User Level    Notice    User root login fail by telnet 186.223.109.178.
20:43:12 03/12/2014    User Level    Notice    User root login fail by telnet 186.223.109.178.
20:42:33 03/12/2014    User Level    Notice    User root login fail by telnet 186.223.109.178.

Now disabled "remote management".

[broadstairs]

My telnet still works OK although I dont need it as I am using an HG612 in bridge mode right now. I had one of the alternate configs loaded which still allows telnet access if you need it after f/w 1.06.

I've had a response from TT this morning where I reported the DHCP failure with this f/w. They have passed it to their product team for investigation which probably means we will not here anything for a week or two.

Stuart

[les-70]

I am considering reverting back to the HG635v1.04t_multicast_with_multicfg_pack.bin from which I had the upgrade work or maybe HG635v1.04t_multicast_with_multicfg_main.bin which has telnet but is further from the 1.04t default TT  settings.

  I may then disable remote update until such time as any real improvements from the original 1.04t firmware are reported by others.  For me 1.06t only has disadvantages and whilst fixing the DHCP would be good the advertised wireless improvements are definitely negative for me. I can't detect a gain with 1.06t

[broadstairs]

Are the other f/w packages available anywhere as sadly I don't have any copies to go back to.

I have asked TT for a copy of 1.04 since their update gave me an issue I didn't have before. Don't hold your breath though.

Stuart