Hi,
I realise the last post was a few months ago now, but I'm trying to figure out which of the values from the vdsl status counts indicates the xDSL sync time. If I look at my modem / system uptime from show status I see 622:0:28 (hh:mm:ss).
> show status
System Uptime:622:0:28
LAN Status
Primary DNS:8.8.8.8 Secondary DNS:8.8.4.4
IP Address:192.168.255.10 Tx Rate:298836061 Rx Rate:471630364
WAN 1 Status: Disconnected
Enable:Yes Line:xDSL Name:
Mode:PPPoE Up Time:0:00:00 IP:--- GW IP:---
TX Packets:0 TX Rate:0 RX Packets:0 RX Rate:0
WAN 2 Status: Disconnected
Enable:Yes Line:Ethernet Name:
Mode:--- Up Time:0:00:00 IP:--- GW IP:---
TX Packets:0 TX Rate:0 RX Packets:0 RX Rate:0
VDSL Information: VDSL Firmware Version:05-07-06-0D-01-07
Mode:17A State:SHOWTIME TX Block:0 RX Block:0
Corrected Blocks:12057 Uncorrected Blocks:470
UP Speed:14292000 Down Speed:50222000 SNR Margin:2 Loop Att.:21
I found the sys diag_log log command useful to see what's happening on the xDSL and from this I can see the last time the line state changed was roughly 596:51:30 since the modem was booted. The exact uptime when the line last changed from "Train(6) to Showtime(7)" was 596:52:08.
596:51:33 [DSL] Line state has changed: 00000801 -> 00000860
596:51:33 [DSL] Status was switched: Showtime(7) to ShutDownWait(15)
596:51:33 [DSL] Line state has changed: 00000860 -> 00000001
596:51:33 [DSL] Status was switched: ShutDownWait(15) to ShutDownReached(16)
596:51:33 [DSL] Status was switched: ShutDownReached(16) to Exception(8)
596:51:33 [DSL] Training Exception:DSL autoboot exception!! exception cnt:1
596:51:35 [DSL] Status: DSL line down by exception
596:51:35 [DSL] Status was switched: Exception(8) to Restart(10)
596:51:35 [DSL] Line state has changed: 00000001 -> 00000000
596:51:35 [DSL] Status was switched: Restart(10) to FirmwareRequest(1)
596:51:35 [DSL] Line state has changed: 00000000 -> 000000FF
596:51:35 [DSL] Training Exception Workaround: reload the same modem code
596:51:35 [DSL] Entering VDSL2 mode
596:51:35 [DSL] modem code: [05-07-06-0D-01-07]
596:51:35 [DSL] Status was switched: FirmwareRequest(1) to firmwareReady(3)
596:51:36 [DSL] Line state has changed: 000000FF -> 00000100
596:51:36 [DSL] Status was switched: firmwareReady(3) to Init(5)
596:51:36 [DSL] >> nXtseA=0d, nXtseB=00, nXtseV=07, nFwFeatures=9
596:51:36 [DSL] >> nHsToneGroupMode=0, nHsToneGroup=102, nToneSet=3, nCamState=2
596:51:36 [DSL] Enable BT related fixes.
596:51:36 [DSL] dms 549 0 2 240B 0.
596:51:36 [DSL] Line state has changed: 00000100 -> 00000100
596:51:36 [DSL] Line state has changed: 00000100 -> 00000200
596:51:36 [DSL] Status was switched: Init(5) to Train(6)
596:51:39 [DSL] Line state has changed: 00000200 -> 00000300
596:51:42 [DSL] Line state has changed: 00000300 -> 00000380
596:52:06 [DSL] Line state has changed: 00000380 -> 00000801
596:52:07 [DSL] Record last show time mode: VDSL2
596:52:08 [DSL] Status was switched: Train(6) to Showtime(7)
596:52:09 [DSL] ActualNetDataRateUs=14292000, ActualNetDataRateDs=50222000
596:52:09 [DSL] VDSL2: UP rate=0, DOWN rate=47983 Kbps, Mode=17A
596:52:09 [DSL] G.Vectoring Status: OFF
596:52:21 [DSL] CPE Inventory:
596:52:21 [DSL] G994VendorID: B5 00 49 46 54 4E 00 00
596:52:21 [DSL] SystemVendorID: B5 00 49 46 54 4E 00 00
596:52:21 [DSL] VersionNumber: 33 2E 38 2E 31 2E 32 5F 42 54 00 00 00 00 00 00
596:52:21 [DSL] SerialNumber: 30 30 31 64 61 61 38 64 61 65 36 63 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
596:52:21 [DSL] XTSECapabilities: 00 00 00 00 00 00 00 07
596:52:21 [DSL] CO Inventory:
596:52:21 [DSL] G994VendorID: B5 00 42 44 43 4D A4 8C
596:52:21 [DSL] SystemVendorID: B5 00 42 44 43 4D 00 00
596:52:21 [DSL] VersionNumber: 76 31 30 2E 30 39 2E 31 32 20 20 20 20 20 20 00
596:52:21 [DSL] SerialNumber: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
596:52:21 [DSL] XTSECapabilities: 00 00 00 00 00 00 00 00
So if I convert the 622:00:28 to seconds (2,239,228) and subtract 596:52:08 (2,148,728) from it I get 90,500 seconds. But when I look at the numbers from the vdsl status counts command I don't see anything that matches.
> vdsl status counts
[ Counters: Showtime ]
Near End Far End Note
ElapsedTime : 1920487 1920487 (seconds)
CRC : 442 12057
FEC : 0 249413
HEC : 0 0
CRC_P : 29 0
CRCP_P : 0 0
CVP_P : 0 0
NCD : 0 0
LCD : 0 0
ES : 110 11366
SES : 18 56
LOSS : 1 7
UAS : 0 0
LOFS : 0 0
[ Counters: 15Min ]
Near End Far End Note
ElapsedTime : 26 26 (seconds)
CRC : 0 0
FEC : 0 9
HEC : 0 0
CRC_P : 0 0
CRCP_P : 0 0
CVP_P : 0 0
NCD : 0 0
LCD : 0 0
ES : 0 0
SES : 0 0
LOSS : 0 0
UAS : 0 0
LOFS : 0 0
[ Counters: 1DAY ]
Near End Far End Note
ElapsedTime : 79226 79226 (seconds)
CRC : 449 14
FEC : 0 11414
HEC : 0 0
CRC_P : 32 0
CRCP_P : 0 0
CVP_P : 0 0
NCD : 0 0
LCD : 0 0
ES : 134 1
SES : 29 0
LOSS : 0 0
UAS : 0 0
LOFS : 0 0
Am I missing something here?
Regards