Kitz ADSL Broadband Information
adsl spacer  
Support this site
Home Broadband ISPs Tech Routers Wiki Forum
 
     
   Compare ISP   Rate your ISP
 
Please login or register.

Login with username, password and session length
Advanced search  

News:

Pages: 1 ... 54 55 [56]

Author Topic: ZyXel VMG8324-B10A Firmware  (Read 212197 times)

george7272

  • Member
  • **
  • Posts: 34
Re: ZyXel VMG8324-B10A Firmware
« Reply #825 on: November 19, 2017, 06:13:33 AM »

My router does not loose configuration but I want to increase the SNR a bit from 6 to 8.
but the adslctl command is not preserved.
I do see some save configuration but I am not sure if this save has to do with the adslctl commands
Logged

burakkucat

  • Global Moderator
  • Senior Kitizen
  • *
  • Posts: 20605
  • Over the Rainbow
    • The ELRepo Project
Re: ZyXel VMG8324-B10A Firmware
« Reply #826 on: November 19, 2017, 05:05:39 PM »

Ah, I see.

It is not the SNR but the target SNRM that you would like to increase. Unfortunately there is no way of saving such an adjustment in the device configuration.
Logged
:cat:  100% Linux and, previously, Unix. Co-founder of the ELRepo Project.

Please consider making a donation to support the running of this site.

george7272

  • Member
  • **
  • Posts: 34
Re: ZyXel VMG8324-B10A Firmware
« Reply #827 on: January 14, 2018, 03:38:17 AM »

Recently I noticed another problem.
I temporary use an external access point and i tried to disable 8924's internal wifi.
If i disable the 2.4 I see the 5g enabled, I go and I disable the 5g and then I see the 2.4g enabled.
Strange behavior
I disabled both from the config file. The status shows that both are disable. I go to the wireless page to
see them and i see one of them is again enabled.
Have you seen that before?
Can you try to disable them for few mins to see if you have the problem?
Logged

machare

  • Member
  • **
  • Posts: 30
Re: ZyXel VMG8324-B10A Firmware
« Reply #828 on: January 14, 2018, 05:05:02 PM »

The wifi of my VMG8924-B10A switches off an on as I would expect. I am using version 19 of the firmware
Logged

bkehoe

  • Just arrived
  • *
  • Posts: 11
Re: ZyXel VMG8324-B10A Firmware
« Reply #829 on: January 14, 2018, 05:13:46 PM »

Same here, latest firmware and both 2.4 and 5GHz wifi disabled.
Logged

george7272

  • Member
  • **
  • Posts: 34
Re: ZyXel VMG8324-B10A Firmware
« Reply #830 on: January 16, 2018, 01:33:30 PM »

Can you go to the wireless page and check it?
Don't click it but just see the page.
The status page shows that are disabled but as soon as I go to the wireless page
shows that are enabled or at least one
Logged

aepos

  • Just arrived
  • *
  • Posts: 1
Re: ZyXel VMG8324-B10A Firmware
« Reply #831 on: January 16, 2018, 02:02:17 PM »

Hi Folks my VMG8324-B10A has been running fine for ages now with V14 firmware, however i have now noticed that I can no longer access the "home Networking" tab just responds with a blank page. everything else is fine. Used Firefox, Safari and Chrome all with the same results. Have restarted the router and reinstalled the saved config file but still the same problem.


Any thoughts? Thanks Ae
Logged
Pages: 1 ... 54 55 [56]
 

anything